RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Max_Power
Showing results 1 to 25 of 500
Search took 0.57 seconds.
08-29-2014, 06:48 AM
Replies: 18
Views: 2,672
Posted By Max_Power

You have blasted me out of the RCU lurking black...

You have blasted me out of the RCU lurking black hole. I've always dreamed of a 1/2A F4!!!! More Please?! Can't wait too see! Todd
03-19-2014, 05:31 PM
Replies: 11
Views: 899
Posted By Max_Power

http://www.alienaircraft.com/k301.htm This...

http://www.alienaircraft.com/k301.htm This thing is on my list, I think it would be a perfect flyer with a Norvel, And look who designed it, The man himself Thomas Herr!!
03-15-2013, 05:19 PM
Replies: 33
Views: 1,830
Posted By Max_Power

RE: How many have flown at Muncie?

I was on a trip from Texas to Indy a few years ago and went to go check out the museum, which was pretty neat. I took along my Gasser heli and got a flight in so I could say I did. A group of guys...
03-01-2013, 04:43 PM
Replies: 288
Views: 25,988
Posted By Max_Power

RE: Mini F-16 vintage project consideration

Don't worry about me wasting any money air raptor, I'm not planning on buying one of those fans....I'd just like to look at one to "investigate" out of curiosity. As it has a aluminum hub and there...
02-26-2013, 01:48 PM
Replies: 16
Views: 1,424
Posted By Max_Power

RE: PAW .15 muffler leakage

Thanks guys....I guess I'll at least chuck it up and measure run out the next time I pull it apart. I have marked everything when I took it apart to minimize "reseat" wear. I did notice that the...
02-25-2013, 10:40 AM
Replies: 288
Views: 25,988
Posted By Max_Power

RE: Mini F-16 vintage project consideration

I wonder if anyone has tried to use one of these fan units http://www.horizonhobby.com/products/delta-v-15-69mm-electric-ducted-fan-EFLDF15 and tried to convert to glow? I saw them at my LHS a few...
02-24-2013, 05:45 PM
Replies: 16
Views: 1,424
Posted By Max_Power

RE: PAW .15 muffler leakage

Thanks RF and AMB, I stock the engine in liquid and did the air test and honestly it still leaks pretty horrible, almost as if the bolts tighten down before the collector and gaskets are...
02-24-2013, 03:13 PM
Replies: 16
Views: 1,424
Posted By Max_Power

RE: PAW .15 muffler leakage

Yeah, changing seals would be a pretty obvious solution, but I wanted to make sure noone said " they all leak there" or "look at this spot right here and see if x-problem exists" etc first. I did...
02-24-2013, 01:10 PM
Replies: 16
Views: 1,424
Posted By Max_Power

PAW .15 muffler leakage

My PAW .15 leaks more oil around the muffler than through it. This is a just broken in engine and I have made sure the head bolts are tight. I've seen some glow engines spit out the Carb and...
02-19-2013, 08:42 PM
Replies: 16
Views: 1,430
Posted By Max_Power

RE: MP Jet diesel troubles

Hey "The Woodlands"! That's my hometown for the first 28 years of life! I bet its much nicer weather there than here right now....If this is your first diesel it might not be a bad idea to buy a...
02-19-2013, 08:27 PM
Replies: 51
Views: 4,595
Posted By Max_Power

RE: Guillow's Zero

Wow Tim, that looks incredible!, when are we going to the field? (Just kidding, I'm too big of weenie to even move my chair away from the heater vent with the weather the last few days BRrrrrr!) I...
Forum: Glow Engines
02-17-2013, 11:32 AM
Replies: 65
Views: 6,664
Posted By Max_Power

RE: OS .10FP

I haven't run mine as a diesel although one of the used ones I bought did come with a DDD head, so if you want to experiment you can come by and throw a head and some diesel at it sometime. Its...
Forum: Glow Engines
02-17-2013, 08:23 AM
Replies: 65
Views: 6,664
Posted By Max_Power

RE: OS .10FP

I think that fp will do ya right on the neofun. I think on a 7x3 MA(ma toughness would be a plus over apc on this one) will pull it along well. I have not seen any of these engines "wear out" . I...
01-27-2013, 08:16 AM
Replies: 78
Views: 5,707
Posted By Max_Power

RE: Change of pace.

So the 4th pin "output enable" on the 4 pin setup can be used as a on/off switch for the regulator ?, or will it still drain the lipo over the course of the next few days or weeks?
01-26-2013, 02:42 PM
Replies: 70
Views: 8,386
Posted By Max_Power

RE: Hot engines

How about using something like this? Only cost me a few dollars to make, but it works great for hard stuff like that especially if it doesn't require a super precise cut as far as exact dimension....
01-26-2013, 01:35 PM
Replies: 78
Views: 5,707
Posted By Max_Power

RE: Change of pace.

I've made and used some regulators exactly like boomerand has shown and been very happy with them. I'm not sure the polarity of the diagram is correct though? It shows battery positive going straight...
01-24-2013, 07:30 PM
Replies: 9
Views: 2,955
Posted By Max_Power

RE: New Edge 540 from Guillows

I've messed with a few of the laser cut Guillow's kits and although I haven't weighed the wood the pieces they were cut pretty well etc. Its nice to see they are adding a few new kits, they have a...
01-21-2013, 06:58 PM
Replies: 51
Views: 4,595
Posted By Max_Power

RE: Guillow's Zero

Hey, that thing is looking good! Looks like your aileron plan worked out fine. Is 7 ounces everything except covering and trim?
01-17-2013, 07:05 PM
Replies: 40
Views: 2,456
Posted By Max_Power

RE: Forum Manners

The search before new post thing seems a bit silly to me sometimes, ...I think these forums are as much for enjoying conversing with others as much as for a pure data reference. Its kinda like...
Forum: Glow Engines
01-14-2013, 01:51 PM
Replies: 32
Views: 5,481
Posted By Max_Power

RE: K&B 3.5 engines

I have a brand new one that I hope to run soon. Tim, mine just has a CL venturi. on it ...which is huge! It also has a pressure tap on a rear cover bolt, which I'm sure it will need with that big...
12-24-2012, 04:59 PM
Replies: 100
Views: 7,685
Posted By Max_Power

RE: In 2013 I resolve to.........

Those are some cool resolutions guys! CP, I'm especially interested in the 1/2a Shrike...I've often wished those kits were around still..., that and shrikes weren't a pain to cover.

I think my...
12-24-2012, 09:15 AM
Replies: 6
Views: 1,157
Posted By Max_Power

RE: McCoy .049 piston/rod reset

I've had a few of the cox pistons that when reset using the supplied die or something too rigid ended up a bit mushroomed and ending up having a issue fitting into the cylinder again properly, so...
12-23-2012, 10:00 PM
Replies: 6
Views: 1,157
Posted By Max_Power

RE: McCoy .049 piston/rod reset

I did end up turning out a tool to do this job as described, except I ended up just drilling a hole down the tool to slip the rod down instead of the slot in the sidelike the Cox tool. I did get it...
12-23-2012, 09:52 PM
Replies: 17
Views: 1,512
Posted By Max_Power

RE: .010 Help needed please.

You sure you aren't thinking of boat fuel Steve? Boats often run that high of nitro but helis usually run either 15% or 30%.... usually easier to needle with 30 and a broader needle as you can't...
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.