RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: billdozer1983
Showing results 1 to 14 of 14
Search took 0.06 seconds.
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

You need to replace all the bushings for bearings and upgrade the driveshaft to aluminum.
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

What would be good gears for top speeds I was thinking a 78 turn spur and a 25 pinion ? But not sure
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

Yes i agree first thing you should do is change the bushings to bearings. Where you plan on going with a faster motor you would probly only get 6 runs tops before they melt.And i run a hpi 15 turn...
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

Can you post a pic of the bent drive shaft just courious how it looks
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

Hpi makes a aluminum drive shaft and i believe ya racing does as well but i might be wrong on the ya racing
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

I use a hot racing drive shaft with a flux setup and have no problems with it.
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

I put a hpi flux in mying and that gear lasted 5 mins and all the bushings melted as well in the front and rear. i changed the bushings to bearings and that little black gear has not strippedyet...
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

it is team associated black stealth grease
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

Thanks for the info i put all new bearings and2 new diff pinion hope fully it will last plus i loaded it with black grease
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

doe's anyone know where i can get aluminum bushings becuse i went brushless and melted the plastic ones and is there a better diff gear due to that i also stripped out the plastic gear in the diff...
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

I back in gear i found after tearing apart my e-10 that the reason it was not running right was the gear was not sitting in stright and binding it all up. Newbie mistake. haha
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

go brushless with lipo
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

Ya i just put the hpi flux in it with the stock gears and it is not running good at all not sure if the esc is no good or if the gears are getting bound up.
Replies: 762
Views: 190,856
Posted By billdozer1983

RE: Official HPI E-10 Thread

I have a stock e-10 with a hot racing drive shaft and want to go brushless what is a good brushless set up. I was looking at hpi flux is this a good 1.
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.