Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: Cactus.
Showing results 1 to 14 of 14
Search took 0.05 seconds.
10-28-2003, 05:25 AM
Replies: 288
Views: 37,033
Posted By Cactus.

RE: Outlaw Construction

might sound stupid, but try a 10x4, then you can try prophang, the outlaw isn't just a fast ship, with my old magnum 36 and a Master 11x4 i was doing hang and even tail touch, was great doing low...
10-27-2003, 01:58 PM
Replies: 288
Views: 37,033
Posted By Cactus.

RE: Outlaw Construction

First thing i did was to move all the servos to the top, the to make more room in the radio bay the rudder and throttle servo got cut into the ribs. the hatch was also extended forwards to the...
10-27-2003, 04:18 AM
Replies: 288
Views: 37,033
Posted By Cactus.

RE: Outlaw Construction

thought i was subscribed to this one...
rocket, if your gonna post pics of rudders could you at least post mine so people get it right ;) LOL
...
10-22-2002, 04:04 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

i use my mini pipe to launch sometimes. i dont trust the fin to hole as its thin and isnt that solid being the hatch, but if im quick and dont throttle up before flying i can launch before it gets to...
10-21-2002, 03:25 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

what about.....
getting those round yogurt pots with bits in a smaller part.. cutting the larger bits out, and installing them in the wing like on Rapiers. would be much easier to launch
10-21-2002, 03:08 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

LOL video one....
buzzzzzzzz.... clunk... " what happened? "
your thrower cant :p
hold the plane in front of you, hands around the LE, at 30-40 degrees nose up, stand still, and throw. Be prepared...
10-09-2002, 03:20 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

reduce the colours, reduce the bite rate you save at, and save as Jpeg, reduce the un-needed frame of the pic, just have subject. it all asves space. my big saver on pics i post here, i save as 50%...
10-07-2002, 03:00 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

i tried doing the Splat, but the poor Magnum 36 and pipe was popping at over rev on the way down, spun well tho. went for new bearings a few days later :D
on that engine and Weston Uk pipe, 10x4 APC...
09-13-2002, 03:21 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

cut holes in the ribs and slide them in there, solves all those problems ;)
09-09-2002, 03:43 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

shes stable, and you've got throttle control, just dont fly it on high rates. i almost killed it test flight when i banked left and did 2 rolls!!!!
09-09-2002, 03:07 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

yours makes mine look like a cavern inside :p
i must have done the fin post diffrent too, i swear i've got room right to the back... yes i did, my solid part of fin is much smaller so the back end...
09-05-2002, 07:37 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

SPRUCE!!!! i used soft 1/4x1/4 balsa and i've survived a head on crash with only loosing the wing tip
08-30-2002, 03:15 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

looking good, dont forget to add the bearers for the wing mounted servos at this point and cut the servo holes in the centre ribs, also the paper tubes for the wing servos.
08-28-2002, 03:18 PM
Replies: 288
Views: 37,033
Posted By Cactus.

Outlaw Construction

that jig thing works a treat. looks about 7 hours from being finished ;)
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.