RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: 3D2000
Showing results 1 to 11 of 11
Search took 0.72 seconds.
02-22-2002, 07:54 PM
Replies: 2
Views: 501
Posted By 3D2000

Morris Knife ARF Control Throw

About to finish the Knife ARF with OS 72 surpass and have the tank outside the wing for ease of maintainence and peace of mind of possible fuel leaking.

The ARF manual does not mention the control...
02-22-2002, 08:11 AM
Replies: 27
Views: 2,633
Posted By 3D2000

Edge 540 Profile review.

vertigo, Aerosplat

If I understand you correctly, I may not have made myself clear enough. I meant the "lateral" balance when the plane is in knife edge position, that is canopy to belly balance,...
02-21-2002, 04:55 PM
Replies: 27
Views: 2,633
Posted By 3D2000

"lateral balance" in knife edge

>> 4. Better lateral balance. I did not have to add weight to either wingtip.
<<

I don't know whether it makes sense or not, is the "lateral balance" important when the plane is in knife edge?
...
Forum: ARF or RTF
01-22-2002, 08:07 PM
Replies: 3
Views: 849
Posted By 3D2000

Hangar 9, 80" Cap 232 info needed

Just talked to Horizon, I asked what is the weight and wing area, the only thing they'd tell me is they tested with Moki 2.10 and Zenoiah 45. What prop and rpm can those engines turn?

KC.
Forum: ARF or RTF
01-22-2002, 06:09 PM
Replies: 3
Views: 849
Posted By 3D2000

Hangar 9, 80" Cap 232 info needed

Does anyone know what weight and wing area are for the yet to be released 80" Cap 232 from H9 ? If it is too heavy for an OS 1.60 which I already have, I might just skip this one and go to 1/3 Cap...
01-18-2002, 03:38 PM
Replies: 2
Views: 667
Posted By 3D2000

Profile (Morris) needs right thrust, mounting engine on LHS ?

I just got my Morris Knife Profile ARF and I notice the engines on most of the profiles I saw is on the right hand side of the fuse.

However, I recently built a Radical rc Edge electric profile,...
Forum: ARF or RTF
01-03-2002, 11:07 PM
Replies: 9
Views: 1,404
Posted By 3D2000

Thank you.

Thank you pileosticks and others for all the info.

KC.
Forum: ARF or RTF
12-31-2001, 06:32 PM
Replies: 9
Views: 1,404
Posted By 3D2000

Engine choice

pileosticks,

What engines and props combo do you use. I have a Magnum 46 that I have not used for years to put it in. I may try OS surpass 70 or get a saito 72 or 52 if the OS is too heavy.
...
Forum: ARF or RTF
12-31-2001, 05:54 PM
Replies: 14
Views: 1,706
Posted By 3D2000

Edge 540, H9 or Lanier???

I was going to order the H9 Edge and found out Lanier got an Edge ARF too, it is about a pound lighter. Does anyone know how do they stack up with each other in the 3D department. Any snap out...
Forum: ARF or RTF
12-31-2001, 05:36 PM
Replies: 9
Views: 1,404
Posted By 3D2000

Re: Knife ARF

I ordered my Morris Knife ARF last week, I was told I should receive it before Jan 10.

KC.
12-23-2001, 10:38 PM
Replies: 3
Views: 1,126
Posted By 3D2000

Pizazz 3D Capabilities

Just got my Pizazz, going to put an OS 70 surpass in it.

I heard a lot of comment about the plane but almost nothing about the 3D capabilities, like elevator, waterfall, harrier and etc. Can...
Showing results 1 to 11 of 11


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.