RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: ulfsve
Showing results 1 to 17 of 17
Search took 0.31 seconds.
03-22-2009, 03:15 PM
Replies: 6
Views: 779
Posted By ulfsve

RE: AR9100 uneven battery use

Thanks,

I missed this.
So I think I will have to switch cables then after 3-4 flights.

Next time I will get servos operating directly on 2S LiPos.

//Ulf
03-22-2009, 08:32 AM
Replies: 6
Views: 779
Posted By ulfsve

RE: AR9100 uneven battery use

Yeah, this is what is worrying me.

But I did some additional testing. The AR9100 has one blue led for each battery showing usage.
At idle only the one coming from line with regulator with...
03-22-2009, 04:09 AM
Replies: 6
Views: 779
Posted By ulfsve

RE: AR9100 uneven battery use

Thanks.

This seems to be the case. One outputs 6.09V and the other 6.04V
Is this a problem or will it fix itself in the end?
Will one be totally drained befor the first is really used?

...
03-20-2009, 03:35 PM
Replies: 6
Views: 779
Posted By ulfsve

AR9100 uneven battery use

Hi,

I flew for the first time with new QQ 86" yak (50cc) where I'm using AR9100. I have 2 1800mAh LiPo with Spektrum power regulators.
Since it where first flight and first run for DA50 I did...
03-16-2009, 01:22 AM
Replies: 2
Views: 291
Posted By ulfsve

RE: 86" Yak Different angle of attack on stab halfes

Thanks for this fast reply Reza!

I assume this means that wing shall have +0.5?

/Ulf
03-15-2009, 08:25 AM
Replies: 2
Views: 291
Posted By ulfsve

86" Yak Different angle of attack on stab halfes

Hi,

When finalizing radio mount and servo setup i discovered angle of attack differs between stab halves.
I measured and found right to be +0,5 degrees and left to be -2,0degrees!!!
This...
03-12-2009, 06:34 AM
Replies: 9
Views: 748
Posted By ulfsve

RE: balancing 86"

Hi,

How much fuel have you had when balancing?
03-09-2009, 03:43 AM
Replies: 0
Views: 548
Posted By ulfsve

DX7/AR6300 and cheap digital servo interference?

Hi,

Since about a year I've been using DX7 with various recievers and servos.
When flying indoors I use AR6300 in my 3D foamies. At first I used cheap chinese digital servos and not seldom...
03-09-2009, 02:59 AM
Replies: 5
Views: 821
Posted By ulfsve

RE: BLS351 Servo centering problem

Hi,

Sorry for my eagerness. You know what it's like when you are about to finish a new model.

//Ulf
03-08-2009, 03:37 PM
Replies: 1
Views: 258
Posted By ulfsve

Standoff length for 86" Yak

Hi,

I have a DA50 with 1 1/4" standoffs as proposed in the manual.
In my opinion the standoffs are to long to for having a real nice fit with spinner/cowl.

Should it be this way?

...
03-08-2009, 03:32 PM
Replies: 5
Views: 821
Posted By ulfsve

RE: BLS351 Servo centering problem

HELLOOOOO!!![sm=75_75.gif]

Anybody here!!!
03-06-2009, 12:57 PM
Replies: 5
Views: 821
Posted By ulfsve

RE: BLS351 Servo centering problem

Hello!

Isn't any Futaba specialists here???
03-06-2009, 07:49 AM
Replies: 5
Views: 821
Posted By ulfsve

BLS351 Servo centering problem

Hi,

I have a 86" Yak (50cc engine class).
For this aircraft I have bought BLS351 servos for rudder and elevator.
Problem is that after installing rudder servo it will vibrate (not only...
03-05-2009, 12:07 PM
Replies: 2
Views: 316
Posted By ulfsve

RE: 86" Yak wheel pants mount

Big thanks! those where the pictures I was looking for.

/Ulf
03-05-2009, 12:03 PM
Replies: 3
Views: 250
Posted By ulfsve

RE: 86" Yak elevator throw

OK,

thanks!

Looking forward to first flight.

/Ulf
03-05-2009, 09:55 AM
Replies: 3
Views: 250
Posted By ulfsve

86" Yak elevator throw

Hi,

Is anyone really flying with the proposed setup in manual, only 10mm?
That seems extremly low.
03-05-2009, 09:53 AM
Replies: 2
Views: 316
Posted By ulfsve

86" Yak wheel pants mount

Hi friends!

I'm building my first QQ model and have come to the landing gear. BUT I don't really understand how whell pants shall be fixed.
Should I use a separate screw through landing gear...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information

Copyright 2018 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.