RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: BobH
Showing results 1 to 25 of 500
Search took 1.46 seconds.
12-02-2021, 07:34 AM
Replies: 76
Views: 13,943
Posted By BobH

Latex paint

Min wax clear can be bought in a spray can. It worksmwell over Latex. They have both clear and satin. Warn the can before using to get a fiber spray.
11-28-2021, 10:35 AM
Replies: 19,457
Views: 2,456,960
Posted By BobH

FYI I have the Peter Barth 1/4 waco unstarted....

FYI I have the Peter Barth 1/4 waco unstarted. Doubt I'll live long enough to build it ;(.
Contact me if Interested.
Forum: Glow Engines
11-28-2021, 10:34 AM
Replies: 3,895
Views: 721,741
Posted By BobH

FYI I happen to have an UMS 777 radial that was...

FYI I happen to have an UMS 777 radial that was barely used. I bought a new carb (OS) for it and never put it on.
I think It'll perform much better with the OS carb.
Contact me if interested.
11-28-2021, 07:58 AM
Replies: 19,457
Views: 2,456,960
Posted By BobH

Waco

That's the Peter Barth 1/3 waco.
10-30-2021, 05:51 AM
Replies: 283
Views: 64,069
Posted By BobH

Carf p-51

Good work Nick !
10-13-2021, 08:53 AM
Replies: 3,838
Views: 758,137
Posted By BobH

What I've done in the past is to use a...

What I've done in the past is to use a rectangular section of Air Craft ply. Attach this to the wing section and cut a rectangular bit on the Fuse. Works pretty well and seemed to wear better than...
10-12-2021, 06:00 AM
Replies: 283
Views: 64,069
Posted By BobH

Carf P51

Nick, looking really good so far. :)
09-16-2021, 08:54 AM
Replies: 158
Views: 43,349
Posted By BobH

Very nice looking plane. Good job!

Very nice looking plane. Good job!
09-16-2021, 08:50 AM
Replies: 4,698
Views: 721,588
Posted By BobH

Looks good.. nice work.

Looks good.. nice work.
09-16-2021, 06:41 AM
Replies: 5,033
Views: 1,146,029
Posted By BobH

Moki enginee

There are a LOT of people who buy the radial engines who DONT have the pre-requist skills to fiddle and futz to get them to run properly. Is this the fault of the buyer? Probably for some of them...
09-15-2021, 05:24 PM
Replies: 1,052
Views: 285,250
Posted By BobH

Looks good :)

Looks good :)
09-15-2021, 05:23 PM
Replies: 5,033
Views: 1,146,029
Posted By BobH

Radial engines

Obviously you are not an engineer. Engineers, at least decent ones, are paid to produce a product that delivers what its intended design promises. What you seem to be saying is "hey thank you for...
09-12-2021, 10:37 AM
Replies: 5,033
Views: 1,146,029
Posted By BobH

Pity that the designers of the 4K engine didn't...

Pity that the designers of the 4K engine didn't know how to design a decent fuel delivery system. It's not rocket science folks. People have been doing it for ever.
The sad thing is that these...
08-16-2021, 03:18 PM
Replies: 162
Views: 22,393
Posted By BobH

WwI planes

Take a look at Balsa USA. They have several matching your description
Forum: RC Jets
07-21-2021, 05:40 AM
Replies: 79
Views: 10,507
Posted By BobH

Bcm t33

Good luck with the maiden.
07-18-2021, 06:39 AM
Replies: 1,052
Views: 285,250
Posted By BobH

Top RC Zero

Looks really good.
Forum: RC Jets
07-13-2021, 06:45 PM
Replies: 79
Views: 10,507
Posted By BobH

Nice :)

Nice :)
Forum: RC Jets
06-21-2021, 05:54 PM
Replies: 79
Views: 10,507
Posted By BobH

Joe thank you for the Servo Info. FYI the F-80...

Joe thank you for the Servo Info. FYI the F-80 was Bob V's favorite plane to fly.. I'm sure the T-33 will fly equally well. Keep up the good work and good luck on the maiden.
Forum: RC Jets
06-20-2021, 07:16 PM
Replies: 79
Views: 10,507
Posted By BobH

HI, I'm a little late to the party but I do have...

HI, I'm a little late to the party but I do have a question.
I have a BVM F-80 I bought 9? years ago. Since the Recommended JR servos are no longer available what servos are you using for your...
03-31-2021, 08:54 AM
Replies: 411
Views: 50,393
Posted By BobH

Awesome stuff!!!

Awesome stuff!!!
03-27-2021, 02:41 PM
Replies: 411
Views: 50,393
Posted By BobH

Spitfire

Super nice stuff.
03-23-2021, 02:06 PM
Replies: 411
Views: 50,393
Posted By BobH

I'm sure that what ever it is it'll be something...

I'm sure that what ever it is it'll be something good.
03-23-2021, 09:14 AM
Replies: 411
Views: 50,393
Posted By BobH

Nice work!

Nice work!
03-22-2021, 01:27 PM
Replies: 411
Views: 50,393
Posted By BobH

Plexiglass is what I would use. I don't know...

Plexiglass is what I would use. I don't know where you can buy it locally but Mick Reeves sells some material that is pretty good.
03-22-2021, 08:45 AM
Replies: 411
Views: 50,393
Posted By BobH

Sure does look good :)

Sure does look good :)
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2022 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.