RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: 9sec240
Showing results 1 to 25 of 74
Search took 0.09 seconds.
06-21-2010, 10:59 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Glenn, you are going to love that heli!! The B400s are a PITA. I thought you had a Pro already though.

EDIT.. just looked at your sig. Pro Pro!! very nice.
06-07-2010, 10:53 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Glenn, I believe that the gyro menu only works on the AUX2 port on the RX with the 9303 / 9503. This means you need a 7 CH RX in order to use that menu. As Nick mentioned, using GEAR EPAs to adjust...
02-14-2010, 11:27 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

jreue, congrats on the successful flights today. Sounds like the T250 is working out well for you. Put together a vid of your progress. It is winter and any entertainment we can get is helpful.
02-07-2010, 08:00 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

I just repaired a B400 for a guy that had the exact same thing happen. The bearing self destructed.

Glad you are digging the T250. They are great helis.
02-06-2010, 05:57 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

jreue, awesome!!! I have been looking forward to a flight report. Head speed on that bugger at 100% throttle with the stock 15T pinion will be in the low to mid 4k range!!!! My T250 with 16T...
02-03-2010, 11:46 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

I have crashed my T250 half a dozen times. Most of the crashes only hurt the feathering shaft and landing gear. The new SE landing gear is way tougher so replace it with that when you break yours. ...
02-02-2010, 08:09 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Put the screw in from the inside of the frame and the nut on the outside. Your hex drive will fit through the hole in the opposite side of the frame.
01-30-2010, 01:02 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Very clean install. That is hard to do. Good job.
01-30-2010, 01:01 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

jreue, the capacity is a read out of how much energy you are putting back into the battery. That is your single most important reading. Your flight times should be just long enough to put back 80%...
01-29-2010, 08:22 AM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Nice job!! How do you like the super tiny stuff so far?
01-26-2010, 11:24 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Check this out though..... Jasmine's profile....
01-26-2010, 07:36 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Good job on the 400. I am really glad you took the time to watch the vids and really understand how the head should be set up. That alone will get you really far in this hobby. Unfortunately, the...
01-26-2010, 12:55 AM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Glenn, you did a great job wiring that up. I had a hell of a time getting mine to look nice but it is so hard on the Pro. I kind of took the easy way out though and did mine like this.
01-25-2010, 12:21 AM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Glenn, there are differences. The plastics for instance. The true Align plastic vertical and horizontal stabs are more rigid and lighter than the HK ones. Aluminum CNC parts are not as nice as...
01-24-2010, 09:12 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Glenn, I fly two HK450s. One is the older V1 clone and all plastic. I have more flights on it than any other helicopter in my fleet. It is doing me very well. It is currently my orientation...
01-24-2010, 02:11 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Peter, I recently had an issue very similar to that. On this helicopter, the tail servo was jerking around at anything over half throttle. After painstakingly eliminating all potential issues, I...
01-24-2010, 11:52 AM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

AWESOME!!! Made me smile to hear you say that. It is really cool when you KNOW you have done it right and it specs out PERFECTLY.
01-20-2010, 09:04 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

01-19-2010, 11:53 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Link measurements are kind of unimportant. What is important is:

1. The swash is level.
2. Washout arms are level at mid stick.
3. Flybar cage is level.
4. Mixing arms are level at...
01-19-2010, 10:08 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

When your head is set up correctly and you have zero pitch at 50% stick, you will have equal amounts of positive and negative pitch available. This means if you have 10 degrees of positive pitch at...
01-16-2010, 02:01 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

jreue, Something is not set up correctly on your heli or in the TX. If you have zero pitch at mid stick and 5 degrees at high stick, low stick should have 1.5 degrees negative pitch (35% on your...
01-15-2010, 10:08 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

I remember a while back a discussion about soft start on the Trex 600s. Somebody here was having issues with it. I think I later read about it being resolved. Anybody here remember the discussion...
01-14-2010, 12:42 AM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Nick, what setup were you running FBL? I have been thinking about pulling my GU365 off the Gaui Hurricane 200 FES and converting one of my HK450s to FBL.
01-13-2010, 07:12 PM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

You will love that heli. Not sure what your plans are for batteries but Hobby City has Zippy Flightmax 800mAh 3S packs in stock which is what I fly currently. I just got some Turnigy batteries of...
01-13-2010, 08:52 AM
Replies: 15,269
Views: 723,804
Posted By 9sec240

RE: are these blades any good for cp pro?

Jreue, I have bought seven helicopters from Flying Hobby and have had a perfect experience each time. The price on that T250 is on the 24 Hour deal they have. It will expire in 2 hours from now. ...
Showing results 1 to 25 of 74
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2022 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.