RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: skunkwurk
Showing results 1 to 12 of 12
Search took 0.01 seconds.
Forum: RC Jets
12-09-2020, 11:03 AM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

You can get these in different colors at DMP. ...

You can get these in different colors at DMP. There is a red that that a longer heat-sync.

UniLight 4W Flashlight, SHORT, 8mm - White
Forum: RC Jets
12-07-2020, 10:13 AM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

Congrats on the maiden! Woo hoo - Another Rebel!

Congrats on the maiden! Woo hoo - Another Rebel!
Forum: RC Jets
12-07-2020, 10:10 AM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

I looked at the kits and saw there either were...

I looked at the kits and saw there either were options I wanted left out or it came with lights I did not need. I make my own "kit" by ordering just the specific LEDs and counts per the installs. I...
Forum: RC Jets
12-06-2020, 05:41 PM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

Nice kit - I use Uni-Lights and they’re great...

Nice kit - I use Uni-Lights and they’re great sets.
Forum: RC Jets
12-03-2020, 01:34 PM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

I agree, it looks great! I like the canopy, it is...

I agree, it looks great! I like the canopy, it is much nicer than my Orange Pirotti version. My canopy is all black.
Forum: RC Jets
11-04-2020, 09:34 AM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

I have seen very nice jets which were very poorly...

I have seen very nice jets which were very poorly setup that did not yield a very pleasant flying experience. I kind of place builder setup/skill in the same category as pilot flying...
Forum: RC Jets
10-29-2020, 06:50 AM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

That is good news - good luck with it!

That is good news - good luck with it!
Forum: RC Jets
10-20-2020, 10:35 AM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

Bob, I see you opted to install the seam of the...

Bob, I see you opted to install the seam of the pipe downward. I believe common guidance has been to install the seam upwards, in case there is some type of leak. I think the logic being if fuel,...
Forum: RC Jets
10-20-2020, 07:19 AM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

That looks pretty good, I'm not seeing the issue....

That looks pretty good, I'm not seeing the issue. I'm sorry. Is it the installation of the plates in the fuse?
Forum: RC Jets
10-20-2020, 06:25 AM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

Can you post a couple pics of the alignment issue...

Can you post a couple pics of the alignment issue you're describing? I typically put together a wooden jig to center and space the turbine to the pipe. It helps center the turbine relative to the...
Forum: RC Jets
10-19-2020, 02:08 PM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

Yes, Carlos does very nice work. I have a fuel a...

Yes, Carlos does very nice work. I have a fuel a and smoke tank in my Rebel as well, he did a nice job. I just ordered a combo Kero/smoke tank from Carlos for a current project. Can’t wait to see...
Forum: RC Jets
10-19-2020, 12:59 PM
Replies: 1,114
Views: 183,498
Posted By skunkwurk

I presume it didn't smell like fuel? It is...

I presume it didn't smell like fuel? It is possible he used water to rinse the tank out and it was not dry when he assembled it. Did you mention it to Carlos? This post made me go check my steel...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright © 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.