RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
Search: Posts Made By: haas599
Showing results 1 to 12 of 12
Search took 0.06 seconds.
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

@somerenegade

Yeah I had that problem with the dogbone popping out. I just dialed down the steering throw on my remote. I am interested in knowing if the universals fix this also.

@warnicksrule...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

A metal servo plate should not be needed for an e10. A 645MG servo is overkill. Hitec makes "torque" servos and "speed" servos. the 645 is for torque and the 625 is for speed. It doesnt take much...
Replies: 762
Views: 190,862
Posted By haas599

Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

They never tightened up to the plastic like they do on the metal. They will just keep spinning and strip out the hole in the plastic. Just twist it in till the hex is touching the arm and the screw...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

no

the balls will face up on the arms with the bearings and face down on the stock knuckle arms.

If you have to twist the sockets onto the threaded rods, remember that one end is backwards when...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

Broke my first part after going brushless. It was a wheel spacer on the right rear. I got an extra set with the car but was wondering where I could buy some more at online. The breakage could have...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

You dont need either to drift, but both help make your car drift better.

I would suggest that you lock the reardiff only because it is basically free to do using stuff you havelaying around the...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

MY E10 DRIVETRAIN UPGRADES & WALLET DAMAGE:

Replaced bushings with bearings - $10.90

Yeah Racing Aluminium driveshafts - $7.88 main shaft, $2.90 short shaft

Hot Racing Aluminium motor mount...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

I've put 3s in my slash and I have a buddy that runs nothing but 3s. He has WAYmore tranny/driveshaft/spur gear/motor temp.problems than I do. We also run backyard tracks where that extra speed...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

I bought the Thunder AC6 charger for $60 shipped. I would recommend this charger if you don't have one or don't like the one you have.

I run a lipo balance charge @ 5.0Aevery timeI charge a...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

First thing I tried was zip-ties and because the "shock body"( lol, Iknow its questionable to refer to these things as shocks at all) is so small it is hard to get the spring to sit properly. I...
Replies: 762
Views: 190,862
Posted By haas599

RE: Official HPI E-10 Thread

Hello, got a E10 a week ago and this is the best forum thread going for the car so first off, thanks to everyone for the info on this car.

My setup is E10 Mustang with drift conversion with a 19t...
Showing results 1 to 12 of 12


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.