RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: Fitz21
Showing results 1 to 25 of 91
Search took 0.69 seconds.
Forum: T-Rex heli
01-27-2008, 10:48 AM
Replies: 8
Views: 1,063
Posted By Fitz21

RE: Trying to get 0 Pitch at half stick

I agree with tippy. Set your heli up at o degrees center stick mechanically first. then adjust subtrims/trims etc.
Forum: T-Rex heli
11-05-2007, 08:50 AM
Replies: 25
Views: 2,400
Posted By Fitz21

RE: Trex 600 parts

pfatz,
the trex600 is alot of heli and expensive too. Maybe it would be wise to put it on the shelf and get a simulator or find a local person to help you. I've been flying for a while and am...
Forum: T-Rex heli
11-01-2007, 04:49 AM
Replies: 4
Views: 831
Posted By Fitz21

RE: Align 600 ESC question

Druss is correct. Just plug the esc into your receiver.. no need to cut anything. kit also includes the step down for the tail servo /gyro
Forum: T-Rex heli
10-29-2007, 10:34 AM
Replies: 6
Views: 1,553
Posted By Fitz21

RE: Trex 450 Aluminum Case

http://www.fxaeromodels.com//product_info.php?cPath=49_175&products_id=2334

I believe this is what you are looking for.
Forum: T-Rex heli
10-23-2007, 07:32 AM
Replies: 17
Views: 1,630
Posted By Fitz21

RE: Charging Problems...taking 6 hrs for 2200 maH?

lipo cells do not trickle charge. sounds like a battery that has been discharged too much especially if the other battery charges fine i/e charger is good. if you had or you have a CBA battery...
Forum: T-Rex heli
10-20-2007, 02:32 PM
Replies: 6
Views: 746
Posted By Fitz21

RE: Servo arm for a 600E

I used futaba servos. followed guidelines on page 19 and 20 of the manual. Since the servo arms are pull-pull setups, it took quite a bit of adjusting to get the servo buzz under control especially...
Forum: T-Rex heli
08-23-2007, 08:56 PM
Replies: 3
Views: 515
Posted By Fitz21

RE: 450S flybar build and question

wasnt sure if you were talking about the SE version or what. glad you got it figured out. have fun.
Forum: T-Rex heli
08-23-2007, 01:58 AM
Replies: 3
Views: 515
Posted By Fitz21

RE: 450S flybar build and question

Look at the manual. the two control arms are held in place by the two control rods. the control rods have to be installed opposite of each other. i/e the distance from one control arm to the ball on...
07-09-2007, 05:39 PM
Replies: 6
Views: 1,557
Posted By Fitz21

RE: gryo question (GY240)

I dont have a gy240. all my gyros are 401's yet i think the 240 requires avcs to be set on the gyro instead of channel 5. On the 401, you have to have it set to avcs before applying power. You know...
Forum: T-Rex heli
07-09-2007, 05:25 PM
Replies: 12
Views: 977
Posted By Fitz21

RE: Antenna placement, for those with no 2.4 Ghz

it comes with an antenna tube which slides thru a hole in the forward and aft landing gear .
Forum: T-Rex heli
07-05-2007, 04:02 PM
Replies: 6
Views: 605
Posted By Fitz21

RE: Trex 600 Question: EPA and the Tail

did you adjust the end points for channel 4 as well? I am still tuning in my 600. i can go thru my settings if you need them. all i ihave left to do is throttle/pitch curves. had quite a bit of servo...
Forum: T-Rex heli
07-05-2007, 03:58 PM
Replies: 6
Views: 605
Posted By Fitz21

RE: Trex 600 Question: EPA and the Tail

you adjust the limit pot on the gyro itself.
05-23-2007, 12:38 AM
Replies: 10
Views: 1,865
Posted By Fitz21

RE: GLITCH, GLITCH, GLITCH, !!!!!!!!

I am assuming you got a new receiver with the new radio. new crystal as well? Did all that happen after a crash? Since you have two choppers, i would swap receivers so long as you use the same radio....
05-22-2007, 09:58 PM
Replies: 3
Views: 1,564
Posted By Fitz21

RE: Issues with Lite Machines Corona 120 heli

You stated you tried another controller and still no joy. If your certain the walkera controller works fine, then you have pretty much eliminated the speed controller as the problem. Disconnecting...
Forum: Kit Building
04-11-2007, 11:48 AM
Replies: 0
Views: 703
Posted By Fitz21

CG Super Chipmunk paint?

Hello,
I am so close to being finnished with this kit but have ran into a major problem and need your help. I covered the model with ultracote and matched the ultracoate paint (white Hanger 9...
01-07-2007, 07:11 PM
Replies: 0
Views: 546
Posted By Fitz21

Mikado Logo10 3d Set-Up Help

My logo needs some help. Im getting around 5-6 minutes of hovering time and the motor is running about 160-165 degrees F. The heli is set up exactly how rotary magazine reviewed the bird. Here it...
07-16-2006, 10:03 PM
Replies: 10
Views: 2,185
Posted By Fitz21

RE: Problems with a Mega Motors 16-15-3

seems like you have tried everything. This might sound novice, but what have you got to lose; i would check my settings in the transmitter for channel 3. sub-trim, or depending on your radio maybe...
04-21-2006, 11:08 AM
Replies: 1
Views: 929
Posted By Fitz21

RE: Under slung batteries and ballance???

i am basically running the same as you except i changed the landing gear to PART#JRP982151
from Helihobby.com. the gear provides a wider stance than stock and you have the battery mount between the...
03-30-2006, 03:59 PM
Replies: 0
Views: 361
Posted By Fitz21

piccolo cp with futaba T6xh programming

Help me please, this radio is so much more difficult to program than my 9CAP. Anyone have a good setup start to finish for this radio and the CP Piccolo with separates?

The goods:
Viper CPX...
02-16-2006, 02:35 PM
Replies: 2
Views: 344
Posted By Fitz21

Pitch and throttle Mixing help!!!!!

Here is the issue: I have a Futaba 6 channel (T6xHs) transmitter and I am using a 5 channel Berg receiver. since i only have five channels and am not going to use channel 5 for gyro sensitivity, I...
Forum: Glow Engines
01-30-2006, 09:17 PM
Replies: 1
Views: 3,552
Posted By Fitz21

K&B Engine Identification?

I recently acquired a K&B two stroke engine which is brand new. The only markings on the motor besides the K&B logo is a :91 stamped on the rear plate. My concern is that I compared the size of this...
10-27-2005, 06:37 PM
Replies: 4
Views: 933
Posted By Fitz21

RE: Contoller Setup

Hey, did you ever get that heli esc working correctly?
10-20-2005, 10:31 AM
Replies: 4
Views: 933
Posted By Fitz21

RE: Contoller Setup

I have a setting on my controller for soft/hard startup. I believe brake on/ brake off is used to control how you want the motor to shut down when you move the throttle stick all the way down. So...
09-28-2005, 05:12 AM
Replies: 9
Views: 1,685
Posted By Fitz21

RE: Balistic upgrades

Gadget01's response is exactly what one should read if waiting on parts from Matt. You will not be disappointed.
07-19-2005, 01:47 PM
Replies: 4
Views: 894
Posted By Fitz21

RE: corona Brushless setup?

i am running 8 cell 2400mah nicd. your 7 cell will work, just make sure you program the controller for option 2(cutoff voltage=5.0v)if you want to. Of course, Flying fish is correct in stating Lipos,...
Showing results 1 to 25 of 91
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.