RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Notices
 
Search: Posts Made By: 3d-aholic
Showing results 1 to 25 of 500
Search took 0.74 seconds.
Forum: Glow Engines
04-14-2009, 09:04 PM
02-16-2009, 10:39 AM
Replies: 4
Views: 1,017
Posted By 3d-aholic

RE: YS 160 Surging at idle

Be sure that your regulator is nice and clean. I know you said you cleaned it. The plunger should be a nice and shiny piece of brass...not dingy with fuel scum.
02-16-2009, 12:12 AM
Replies: 4
Views: 1,017
Posted By 3d-aholic

RE: YS 160 Surging at idle

Whats the RPM at Idle before it surges?
02-15-2009, 05:27 PM
Replies: 10
Views: 1,295
Posted By 3d-aholic

RE: 63 FZ top end rpm

My engine had no compression and now with the new ring, it has a massive amount of compression. Its actually truely amazing as over time you forget. I think the rings on these little motors can...
02-13-2009, 11:32 PM
Replies: 6
Views: 1,058
Posted By 3d-aholic

RE: YS63 FZ plunger

No its got the bubble impression of the opening...but that happens really quick in my experience. In fact in this one, it happend in 2 months and only about 20 tanks or so of fuel.
02-13-2009, 07:07 PM
Replies: 6
Views: 1,058
Posted By 3d-aholic

RE: YS63 FZ plunger

I already paid for the smaller plunger...
The problem is whats the chances that it leaks now with the diaphram that is 2 months old with the larger plunger?

The point is that YS and Central...
02-13-2009, 05:08 PM
Replies: 6
Views: 1,058
Posted By 3d-aholic

RE: YS63 FZ plunger

Well Central Hobbies should update their website and indicate its not a 100% equivalent replacement product. My regulator has a ledge the larger diaphram rests on and keeps it more "stable" against...
02-13-2009, 11:35 AM
Replies: 6
Views: 1,058
Posted By 3d-aholic

YS63 FZ plunger

I ordered a YS 63 FZ plunger from Central Hobbies, their part# YS1145 as shown on their blowup diagram at http://centralhobbies.com/Engines/parts/YS63FZEx.html. Anyway, the plunger that came is...
02-13-2009, 08:41 AM
Replies: 10
Views: 1,295
Posted By 3d-aholic

RE: 63 FZ top end rpm

The thickness or how big the snip is.
A new ring is $19.50, a bearings set is probably $20 ish, the other parts are probably much cheaper. Those are going to be the "high wear" parts.

Its a...
02-13-2009, 01:22 AM
Replies: 1
Views: 600
Posted By 3d-aholic

RE: Bearings stuck

I hate to use a piece of bent landing gear behind the bearings to apply pressure to pull them back out. Gosh...don't want to do that again. Make sure and put the bearings on the crank first so they...
02-13-2009, 01:19 AM
Replies: 5
Views: 800
Posted By 3d-aholic

RE: YS 63s regulator pink buildup

Yeh, don't use carb cleaner or any heavy petroleum solvents.... I would worry most about the silicon O'ring at the bottom of the diaphram. What happens with these silicon O'rings when you use things...
02-13-2009, 01:01 AM
Replies: 10
Views: 1,295
Posted By 3d-aholic

RE: 63 FZ top end rpm

I have my YS63 currently completely apart and its about to go back together. So if you want a picture of something let me know. That piston is very dirty on top. When I pulled mine after about 6...
02-12-2009, 12:02 AM
Replies: 1
Views: 600
Posted By 3d-aholic

Bearings stuck

Working on this engine has been quite difficult.
Ok, I got the bearings out. Cleaned everything and went to put them back in. Most of the time the rear bearings have no particular orientation. ...
02-11-2009, 08:47 PM
Replies: 8
Views: 1,222
Posted By 3d-aholic

RE: Removing crankshaft and bearings

Ok I got the crank off working on the bearings now.
I returned the $3.99 battery puller and bought a $5.99 gear puller and it seemed to have the muscle to do it. When it came out, it popped under...
02-11-2009, 10:16 AM
Replies: 8
Views: 1,222
Posted By 3d-aholic

RE: Removing crankshaft and bearings

Ok, everything is much tighter than I am use to I guess. Do I have to do anything to put the washer back or will just the pressure of the prop and washer "reseat" it?

Thanks guys....I guess I...
02-11-2009, 01:12 AM
Replies: 8
Views: 1,222
Posted By 3d-aholic

RE: Removing crankshaft and bearings

Yeh, I bought one of those car terminal removal ones from AutoZone. It didn't work. It buggered up the drive washer pretty bad. I kept trying and then the car terminal remover pretty much...
02-10-2009, 11:27 PM
Replies: 8
Views: 1,222
Posted By 3d-aholic

Removing crankshaft and bearings

Any tips on how to remove the crankshaft and bearings out of a YS engine. I have removed bearings out 2 stroke and 4 stroke motors before but nothing I have done before has prepared me it seems on...
02-05-2009, 10:14 AM
Replies: 4
Views: 822
Posted By 3d-aholic

RE: YS63- Factory Default LSN

Ok, thanks guys.
Everything is disassembled already....and getting ready to go back together. I missed or misunderstood the one turn thing in the manual.
02-04-2009, 10:21 PM
Replies: 4
Views: 822
Posted By 3d-aholic

YS63- Factory Default LSN

What is the factory default for the YS63 LS Needle? I'm taking mine apart and I don't see that in the manual.

Looking at screw movement from the inside 2 turns out looks like it centers the...
12-15-2008, 07:28 PM
Replies: 8
Views: 2,545
Posted By 3d-aholic

RE: YS-63 Engine Rebuild

I don't know...but let me know if you call them.
12-11-2008, 05:42 PM
Replies: 27
Views: 4,283
Posted By 3d-aholic

RE: ys engine surging at full throttle

Its a YS63 pre-S version.
I run my engine dry each time.
I fly just about every week or every other week. It rarely sits for a month.

Actually very little rust for 6 years and 40...
12-11-2008, 03:20 PM
Replies: 27
Views: 4,283
Posted By 3d-aholic

RE: ys engine surging at full throttle

Thanks...yeh, I clearly saw fuel coming out of the "rear" of the value gasket cover at the seam line. In addition, I believe the gasket was not 100% when I took it off and put it back but didn't...
12-11-2008, 12:40 PM
Replies: 15
Views: 2,860
Posted By 3d-aholic

RE: Y.S. Piston Gas Port Modification

See image...is this what your talking about doing?
Apologizing in advance for my graphic skills but the top image is looking at the piston from the top and the bottom image is the same piston from...
12-11-2008, 12:19 PM
Replies: 8
Views: 2,545
Posted By 3d-aholic

RE: YS-63 Engine Rebuild

Just not sure about the Piston Ring...
Not even sure exactly how I can tell if it needs a new one when I look at it.

Overhauls have worked very well before me. All kinds of hidden girt and...
12-11-2008, 10:11 AM
Replies: 8
Views: 2,545
Posted By 3d-aholic

RE: YS-63 Engine Rebuild

I don't think I need that...it was running like a raped ape before hand and very reliable. It just needs a light duty overhaul.
Showing results 1 to 25 of 500
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service - Do Not Sell My Personal Information -

Copyright 2021 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.