wicked wreck today snapped off intake head
#1
Member
Thread Starter
Join Date: Dec 2008
Location: Charleston, SC
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
wicked wreck today snapped off intake head
took a wicked roll today and snapped off the air intake head. i'm assuming i got some dirt or dust inside the manifold. can anyone tell me where to go from here. how do i clean it up?
#2
Senior Member
My Feedback: (1)
RE: wicked wreck today snapped off intake head
Personally I would pull everything apart and soak it all in Diesel fuel for a little while. Take one piece out at a time and brush everything off with a soft paint brush, dip it in the Diesel fuel once again, then blow everything off with the air compressor. Wipe everything down with a clean dry cloth or paper towel. Then take another paper towel with after run oil on it, wipe everything down with the after run oil, and reassemble everything.
#3
Senior Member
RE: wicked wreck today snapped off intake head
ORIGINAL: Montana Mike
Personally I would pull everything apart and soak it all in Diesel fuel for a little while. Take one piece out at a time and brush everything off with a soft paint brush, dip it in the Diesel fuel once again, then blow everything off with the air compressor. Wipe everything down with a clean dry cloth or paper towel. Then take another paper towel with after run oil on it, wipe everything down with the after run oil, and reassemble everything.
Personally I would pull everything apart and soak it all in Diesel fuel for a little while. Take one piece out at a time and brush everything off with a soft paint brush, dip it in the Diesel fuel once again, then blow everything off with the air compressor. Wipe everything down with a clean dry cloth or paper towel. Then take another paper towel with after run oil on it, wipe everything down with the after run oil, and reassemble everything.
#4
RE: wicked wreck today snapped off intake head
ORIGINAL: gardnesd
took a wicked roll today and snapped off the air intake head. i'm assuming i got some dirt or dust inside the manifold. can anyone tell me where to go from here. how do i clean it up?
took a wicked roll today and snapped off the air intake head. i'm assuming i got some dirt or dust inside the manifold. can anyone tell me where to go from here. how do i clean it up?
Wait wait, What do you mean by air intake head? The cooling head? Was the inside of your motor visible?
#5
Senior Member
RE: wicked wreck today snapped off intake head
ORIGINAL: fabrimacator21
Wait wait, What do you mean by air intake head? The cooling head? Was the inside of your motor visible?
ORIGINAL: gardnesd
took a wicked roll today and snapped off the air intake head. i'm assuming i got some dirt or dust inside the manifold. can anyone tell me where to go from here. how do i clean it up?
took a wicked roll today and snapped off the air intake head. i'm assuming i got some dirt or dust inside the manifold. can anyone tell me where to go from here. how do i clean it up?
Wait wait, What do you mean by air intake head? The cooling head? Was the inside of your motor visible?
#7
Senior Member
RE: wicked wreck today snapped off intake head
ORIGINAL: thesouth1
I did that one time too! But it wasn't just the head
I did that one time too! But it wasn't just the head
#8
Member
Thread Starter
Join Date: Dec 2008
Location: Charleston, SC
Posts: 32
Likes: 0
Received 0 Likes
on
0 Posts
RE: wicked wreck today snapped off intake head
OMG, no it was the air filter head. don't really know how to take the engine apart. it's a trx 3.3. is there a vid. or do i just go to town.
#10
Senior Member
Join Date: Sep 2006
Location: Xenia,
OH
Posts: 400
Likes: 0
Received 0 Likes
on
0 Posts
RE: wicked wreck today snapped off intake head
ORIGINAL: matts6887
Dang man!!!! what the heck did u do!!!!! [X(]
Dang man!!!! what the heck did u do!!!!! [X(]
ORIGINAL: gardnesd
OMG, no it was the air filter head. don't really know how to take the engine apart. it's a trx 3.3. is there a vid. or do i just go to town.
OMG, no it was the air filter head. don't really know how to take the engine apart. it's a trx 3.3. is there a vid. or do i just go to town.
#11
Senior Member
Join Date: Sep 2006
Location: Xenia,
OH
Posts: 400
Likes: 0
Received 0 Likes
on
0 Posts
RE: wicked wreck today snapped off intake head
ORIGINAL: Montana Mike
dowloaded the parts diagram from Traxxas and use that as a guide to rebuild. It is easy, just pay attention to what you are doing
dowloaded the parts diagram from Traxxas and use that as a guide to rebuild. It is easy, just pay attention to what you are doing
#13
Senior Member
Join Date: Oct 2006
Location: Chapel Hill,
NC
Posts: 1,951
Likes: 0
Received 0 Likes
on
0 Posts
RE: wicked wreck today snapped off intake head
here's a video of how to take it apart. it's probably easier to watch a video than look at a manual. the videos are long but packed with good info...
part 1 http://www.youtube.com/watch?v=RM0BTN58pY4
part 2 http://www.youtube.com/watch?v=EwDZf...eature=related
part 3 http://www.youtube.com/watch?v=DdTUM...eature=related
part 1 http://www.youtube.com/watch?v=RM0BTN58pY4
part 2 http://www.youtube.com/watch?v=EwDZf...eature=related
part 3 http://www.youtube.com/watch?v=DdTUM...eature=related
#14
Senior Member
RE: wicked wreck today snapped off intake head
ORIGINAL: cmerritt
here's a video of how to take it apart. it's probably easier to watch a video than look at a manual. the videos are long but packed with good info...
part 1 http://www.youtube.com/watch?v=RM0BTN58pY4
part 2 http://www.youtube.com/watch?v=EwDZf...eature=related
part 3 http://www.youtube.com/watch?v=DdTUM...eature=related
here's a video of how to take it apart. it's probably easier to watch a video than look at a manual. the videos are long but packed with good info...
part 1 http://www.youtube.com/watch?v=RM0BTN58pY4
part 2 http://www.youtube.com/watch?v=EwDZf...eature=related
part 3 http://www.youtube.com/watch?v=DdTUM...eature=related
#16
Senior Member
RE: wicked wreck today snapped off intake head
ORIGINAL: MurphJato
Heres a picture of my motor off my Jato 3.3........
Heres a picture of my motor off my Jato 3.3........
#17
Senior Member
Join Date: Sep 2006
Location: Xenia,
OH
Posts: 400
Likes: 0
Received 0 Likes
on
0 Posts
RE: wicked wreck today snapped off intake head
ORIGINAL: MurphJato
Heres a picture of my motor off my Jato 3.3........
Heres a picture of my motor off my Jato 3.3........
friggin' sweet, I love seeing the insides of someone elses engine What did you go under to get it to pop like that? When I did mine it landed funny on its lid and made a weird noise.
#18
Member
Join Date: Oct 2007
Location: Lockport,
NY
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
RE: wicked wreck today snapped off intake head
A full-size car snuck up behind me.....by time I saw it, it was too late. I only crushed the motor and rear body post. You think my motor looks bad you should have seen his oil pan...LOL....My parts will cost about 130 total his is alot more. There is nothing salvagable of this motor. Some of the skirt is broke off the crank and connecting rod are both really bent.
#20
Member
Join Date: Oct 2007
Location: Lockport,
NY
Posts: 97
Likes: 0
Received 0 Likes
on
0 Posts
RE: wicked wreck today snapped off intake head
Yep, they said send it in with all the pieces. I even told them there is no way they could rebuild this motor. They said send it.