Community
Search
Notices
WildHare R/C Support Disscuss WildHare RC products in this forum. Please note, answers may be provided by Tom Fawcett (owner of WildHare RC) or by the general membership.

cap 232 help needed

Thread Tools
 
Search this Thread
 
Old 04-21-2007 | 05:52 AM
  #1  
Thread Starter
Junior Member
 
Joined: Jul 2006
Posts: 19
Likes: 0
Received 0 Likes on 0 Posts
From: cayuga, ON, CANADA
Default cap 232 help needed

i have a cap with a da50 in it and was wondering how much right thrust i am going to put in it. when i try to go vertical it pulls hard left
also when knife edge it does weird things, any setup help would be appreaciated
Old 04-21-2007 | 08:43 AM
  #2  
Senior Member
 
Joined: Dec 2005
Posts: 310
Likes: 0
Received 0 Likes on 0 Posts
From: Elko, NV
Default RE: cap 232 help needed

There is no set amount of right thrust. You just have to add it an then test it until it is right. I would start slow. On another Plane, I had to do the same, so I Just started adding washers to the left side (top and bottom ) until it flew right. I think I ended up with about 4 or so. As far as knife edge goes what is wierd things? If that means pitch and roll, it is fairly common on a cap. You can fix some of it with the CG but the rest you will have to mix out with a radio.
Old 04-21-2007 | 08:46 AM
  #3  
rctom's Avatar
Senior Member
 
Joined: May 2002
Posts: 6,189
Likes: 0
Received 2 Likes on 2 Posts
From: Flower Mound (near Dallas), TX
Default RE: cap 232 help needed

The built-in right thrust should be about right. A little added up thrust might help, and check that all the servos are working propoerly.

If it pulls left when you enter an up line (which most planes do) you may want to mix some rudder with the elevator.

I have said many times before that Caps require a lot of trimming and are more of a 3d plane.

TF
Old 04-22-2007 | 02:47 AM
  #4  
Member
 
Joined: Aug 2002
Posts: 54
Likes: 0
Received 0 Likes on 0 Posts
From: Hamilton, ON, CANADA
Default RE: cap 232 help needed

Hi Chris, what kind of weird things does it do in knife edge?

Ron
Old 04-22-2007 | 06:27 AM
  #5  
Thread Starter
Junior Member
 
Joined: Jul 2006
Posts: 19
Likes: 0
Received 0 Likes on 0 Posts
From: cayuga, ON, CANADA
Default RE: cap 232 help needed

in nife edge it goes to the bottom of the plane and rolls left. thats not the weird,if i an say doing a rool donsnt matter which way slow or fast when it gets to the knife edge part it looks like the tail starts to cork screw.But if i go to just knife edge it just does the mentioned.does that mace any sence
Old 04-22-2007 | 06:52 PM
  #6  
Jake Ruddy's Avatar
Senior Member
My Feedback: (40)
 
Joined: May 2005
Posts: 4,105
Likes: 0
Received 1 Like on 1 Post
From: Bear, DE
Default RE: cap 232 help needed

Chris.... you are basically echoing the same issues I have discussed in another thread. You can add 1 or 2 washers for some added right thurst.. but the rest is going to have to be done with Rudder. You will prob need about 2 washers of up thrust as well.

I can tell you that as of today I have about 16% up el. mixed into rudder and about 8% al. to do KE.. it's still not perfect but a lot closer than previous attempts. Slow rolls to KE require a lot of effort to make it look nice because of the amount of mixes needed to make it fly well in KE.

I would consider putting the mixes on a switch because there is much needed that when you go into 3D mode it fights against you... use your rudder and you push the nose as well.

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are On



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.