Mamba help
#1
Senior Member
Thread Starter
Join Date: Dec 2006
Location: toms river, NJ
Posts: 1,087
Likes: 0
Received 0 Likes
on
0 Posts
Mamba help
Ok.. I have a Mamba 25 esc.. I try to caliberate it with my jr xr2 radio and reciever and it reconizes full throttle but not braking.. If i use any other transmitter and reciever it will work fine.. How come it won't work with my jr? batterys? Thanks in advance
#4
Senior Member
Thread Starter
Join Date: Dec 2006
Location: toms river, NJ
Posts: 1,087
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
They are all charged and ive following them like to the dime... it just wont' work with this reciever and transmitter if i do it with my other transmitters it will work....and dasmopar all I have to say to that is no comment
#7
Senior Member
Thread Starter
Join Date: Dec 2006
Location: toms river, NJ
Posts: 1,087
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
Ok.. I figured it out..Its going into programming mode and it has already been caliberated but caliberated wrong.. So now im trying to recaliberate and it won't let me.. like if i swtich transmitters and go back to the jr it saves the settings.. how do i recalibarate it ?
#8
Senior Member
Join Date: Feb 2005
Location: Valdosta,
GA
Posts: 476
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
follow the directions!
it tells you how to go into programming mode
i dont understand why there are so many threads with mamba help
its in the directions!!!!
it tells you how to go into programming mode
i dont understand why there are so many threads with mamba help
its in the directions!!!!
#9
Senior Member
Thread Starter
Join Date: Dec 2006
Location: toms river, NJ
Posts: 1,087
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
Ok if you even read my post i wasn't asking how to go into programming mode so ya... I was asking how to recaliberate a controller that already was caliberated...and just switching to a different controller doesn't work.. it will like rememeber that i already caliberated the controller
#10
Senior Member
My Feedback: (2)
Join Date: Jun 2003
Location: orlando, FL
Posts: 295
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
I agree..... I followed the directions on a dime also, but it didnt work. I got the usb cable and didnt even program it to my remote, i just plugged it in and it worked with out programming it with a tx.
#13
Senior Member
Join Date: Feb 2005
Location: Valdosta,
GA
Posts: 476
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
ORIGINAL: flyingjato3.3
Ok if you even read my post i wasn't asking how to go into programming mode so ya... I was asking how to recaliberate a controller that already was caliberated...and just switching to a different controller doesn't work.. it will like rememeber that i already caliberated the controller
Ok if you even read my post i wasn't asking how to go into programming mode so ya... I was asking how to recaliberate a controller that already was caliberated...and just switching to a different controller doesn't work.. it will like rememeber that i already caliberated the controller
it tells you how to go INTO calibrateing mode!
are all your trims set to zero,and whats the brake set at on your controller...
#14
Join Date: Jan 2007
Location: East Stroudsburg,
PA
Posts: 2,189
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
do as follows:
Disconnect battery
turn mamba switch off
connect battery
mamba will flash all colors
apply full throttle
turn switch on
wait 2 seconds
mamba flashes green and rings 4 times indicating throttle measured
mamba flashes red while beeping
push full brake
wait 1 second
mamba flashes red and rings 4 times indicating brake measured
mamba flashes yellow while beeping
put trigger to neutral
wait 1 second
mamba flashes yellow indicating neutral measured
wait 1 second
mamba will flash all colors and ring once
do those and try it again...
Disconnect battery
turn mamba switch off
connect battery
mamba will flash all colors
apply full throttle
turn switch on
wait 2 seconds
mamba flashes green and rings 4 times indicating throttle measured
mamba flashes red while beeping
push full brake
wait 1 second
mamba flashes red and rings 4 times indicating brake measured
mamba flashes yellow while beeping
put trigger to neutral
wait 1 second
mamba flashes yellow indicating neutral measured
wait 1 second
mamba will flash all colors and ring once
do those and try it again...
#16
Senior Member
Thread Starter
Join Date: Dec 2006
Location: toms river, NJ
Posts: 1,087
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
HOW THE HELL DO U RECALIBERATE IT OR DO ANYTHING IF IT WONT RECNONIZE FULL BRAKE TO GET TO ALMOST ANY STEP YOU NEED FULLL BRAKE AND IT WONT RECNOZIE IT IKM TRYING TO ASK HOW THE FU** TO RECALIVERATE IT... sorry for caps i wrote that whole thing in it and not relizing and i don't feel like righting it over
#18
Senior Member
Join Date: Feb 2007
Location: warrington,
PA
Posts: 774
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
ORIGINAL: flyingjato3.3
TO RECALIVERATE IT...
TO RECALIVERATE IT...
ok, try to take all of the batteries out of everything, take the crystals out of the Rx and Tx. make sure the crystals are correct, put all batteries back in. then try.
is it possible to have a faulty Rx, Tx, and ESC? yes. is it likely, no. i am the WIZARD of user error, so i understand thi whole "user error" feeling, and it's defeat. take your time and try EVERYTHING.
you will get it. :thumbup:
#20
Senior Member
Thread Starter
Join Date: Dec 2006
Location: toms river, NJ
Posts: 1,087
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
I have the castle link..so use the controller where nothing will work except the steering becuase it isn't caliberated correctly? SMART idea.. OMFG im not an idiot I can follow simple directions it was caliberated incorrectly....all I am asking to do is how to recaliberate a controller ?
#23
Senior Member
My Feedback: (1)
Join Date: Mar 2004
Location: Edgerton,
KS
Posts: 109
Likes: 0
Received 0 Likes
on
0 Posts
RE: Mamba help
Increase the endpoints on the throttle and brake to 125%, and make sure your slider (either "A" or "B" near the trigger/wheel) is also out to 125%. Throttle should be in normal. You should be good to go after that. Let me know if it's still a problem.