"OFFICIAL"Redcat Racing 1/10th BUGGY
#576
Member
Join Date: May 2006
Location: Newmarket,
NH
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
HI Lordmik
Thank you for ur reply. But i have noticed in the past that the engine did not die when i used to refill after a spin.
ALso Mark thank your for ur reply. Is it possible to replace the bearing.?? Are parts available ?? This buggy has just done less than 2 qts of run.
What other engines are good for my Himoto syclone 2 speed 4 WD
Thank u guys
Thank you for ur reply. But i have noticed in the past that the engine did not die when i used to refill after a spin.
ALso Mark thank your for ur reply. Is it possible to replace the bearing.?? Are parts available ?? This buggy has just done less than 2 qts of run.
What other engines are good for my Himoto syclone 2 speed 4 WD
Thank u guys
#577
Senior Member
Join Date: Mar 2006
Location: Los Angeles, California,
CA
Posts: 523
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
We have a bearing for the Vertex .18 Taiwan motor. Himotos usually have the Infinity Japan .18
Not sure if the bearing is the same. If you tell me the size I can compare.
Here's a link: http://www.topspeedtoys.com/index.ph...9314d736a375f0
Mark
Not sure if the bearing is the same. If you tell me the size I can compare.
Here's a link: http://www.topspeedtoys.com/index.ph...9314d736a375f0
Mark
#579
Senior Member
Join Date: Mar 2006
Location: Los Angeles, California,
CA
Posts: 523
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
I will get the size of the bearing later today. When and if you get to tearing down the motor check to see if the measurement is the same.
Mark
Mark
#580
Junior Member
Join Date: Aug 2006
Location: moncton,
NB, CANADA
Posts: 11
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
Does anybody know of any wheels that are bigger than the ones that come on the truck that are available? (himoto eldorada/redcat volcano) I'd like to have more ground clearance. Also, are there any other bodies available?
thanks.
Dan
thanks.
Dan
#582
Senior Member
My Feedback: (2)
Join Date: Jun 2004
Location: clarkston,
WA
Posts: 541
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
ORIGINAL: leesmack
hey nitro_racer_1, i was wondering what the aluminum upper plate you have on your car is for? im guessing for reinforcment?? is it a worthy buy?
hey nitro_racer_1, i was wondering what the aluminum upper plate you have on your car is for? im guessing for reinforcment?? is it a worthy buy?
#583
Senior Member
Join Date: Mar 2006
Location: Los Angeles, California,
CA
Posts: 523
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
ORIGINAL: nitro_racer_1
well i wanted to make the truck all aluminum mainly for the strength, just cuz the aluminum is stronger than the plastic, and it prolly stiffens up the chassis a little which is a good thing for handleing, and yeah i would recomend it, carbon fiber is good too, im actualy gonna replace my alluminum upper plate with carbon fiber, ive been in touch with Noob2nitro, who is working with top speed toys to make CF parts for the buggy, if i were u i would hold out for the CF stuff cuz its strong and stiff and really light.
ORIGINAL: leesmack
hey nitro_racer_1, i was wondering what the aluminum upper plate you have on your car is for? im guessing for reinforcment?? is it a worthy buy?
hey nitro_racer_1, i was wondering what the aluminum upper plate you have on your car is for? im guessing for reinforcment?? is it a worthy buy?
shhhh!!!!
#585
Member
Join Date: May 2006
Location: Newmarket,
NH
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
HI Mark , Hi all
On the front engine bearing , is there a part number as per the manual ?. I see in my manual as
02079 - OIL BEARING 15*10*4.
Is it called Oil Bearing or engine bearing ...are both one and the same ? will this fix my problem of fuel leak that i see when i prime the engine?? Does the front and back bearing usually have the same size.
thank you
On the front engine bearing , is there a part number as per the manual ?. I see in my manual as
02079 - OIL BEARING 15*10*4.
Is it called Oil Bearing or engine bearing ...are both one and the same ? will this fix my problem of fuel leak that i see when i prime the engine?? Does the front and back bearing usually have the same size.
thank you
#586
Senior Member
Join Date: Mar 2006
Location: Los Angeles, California,
CA
Posts: 523
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
ORIGINAL: lucasdon17
HI Mark , Hi all
On the front engine bearing , is there a part number as per the manual ?. I see in my manual as
02079 - OIL BEARING 15*10*4.
Is it called Oil Bearing or engine bearing ...are both one and the same ? will this fix my problem of fuel leak that i see when i prime the engine?? Does the front and back bearing usually have the same size.
thank you
HI Mark , Hi all
On the front engine bearing , is there a part number as per the manual ?. I see in my manual as
02079 - OIL BEARING 15*10*4.
Is it called Oil Bearing or engine bearing ...are both one and the same ? will this fix my problem of fuel leak that i see when i prime the engine?? Does the front and back bearing usually have the same size.
thank you
No lucas, 02079 is a brass bushing for the wheel hub. Comes w/ basic RTR nitros. Better RTR's have bearings there but this
is not an engine bearing. Also, no engine parts are listed in the manuals.
You need item R011... see attached pic.
Mark
#588
Senior Member
Join Date: Mar 2006
Location: Los Angeles, California,
CA
Posts: 523
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
ORIGINAL: lucasdon17
Thank you so much for the clarification.
Did u get a chance to check the measurements of the bearing ?
Thanks again
Thank you so much for the clarification.
Did u get a chance to check the measurements of the bearing ?
Thanks again
I'll have to try to get that info tonight.
Mark
#590
Member
Join Date: May 2006
Location: Newmarket,
NH
Posts: 49
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
Hey mitch46701
Looks like all the snaps are out of focus. May be u wanna click on the button that has the FLOWER like marking and then click close in pictures. It worked for me fine. Just a suggestion.
Bye
Looks like all the snaps are out of focus. May be u wanna click on the button that has the FLOWER like marking and then click close in pictures. It worked for me fine. Just a suggestion.
Bye
#593
Senior Member
Join Date: Jul 2006
Location: Rocky Hill, CT
Posts: 276
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
mitch, is that the HPI threaded clutchbell I've heard a lot of talk about? And is that a home made aluminum tranny case?
ORIGINAL: mitch46701
well guys heres my tranny pics sorry took so long but was waiting to be able to upload pics
well guys heres my tranny pics sorry took so long but was waiting to be able to upload pics
#596
Junior Member
Join Date: Jun 2006
Location: Albion, IN
Posts: 29
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
yes thats a 2 speed hpi clutch bell that is the original tranny case with an hpi 86038 2 speed tranny kit installed its an hpi onroad setup but have had no problems with it shifting it runs good the engine doesnt wanna wind out 2nd though think its just a lack of power i could tweak the shift point a little though the engine has a weak top end think ill stick to my orinigal idea of slapping a OS .18 tz in it that should give me the power needed to wrap it out
#597
Senior Member
Join Date: Mar 2006
Location: Los Angeles, California,
CA
Posts: 523
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
ORIGINAL: lucasdon17
HI Mark, Hi All
Does the front engine bearing look something like this in the attachement.
Thank you
HI Mark, Hi All
Does the front engine bearing look something like this in the attachement.
Thank you
I measured front engine bearing for VX18 taiwan motor at 19 x 10 x 5
Mark
#599
Senior Member
My Feedback: (2)
Join Date: Jun 2004
Location: clarkston,
WA
Posts: 541
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
also if its leaking at the front of the motor, i would check the seal at the botom of the carb, or the nut that holds it on could be loose.
#600
Senior Member
My Feedback: (2)
Join Date: Jun 2004
Location: clarkston,
WA
Posts: 541
Likes: 0
Received 0 Likes
on
0 Posts
RE: "OFFICIAL"Redcat Racing 1/10th BUGGY
hey mitch, i noticed in your pics your wheels and gas tank, wered u get them?, especially the tank, and could u post a pic of the wheels, i just bought some jato wheels/tires for mine but im always looking for extras and thoes look like they might be pretty nice.