Any problem with Mintor22
#1
Member
Thread Starter
Join Date: Feb 2010
Location: Sabadell, SPAIN
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
Any problem with Mintor22
Hello;
I bought a Mintor22. I like to know if anyone has had a problem with the engine.
I appreciate your answers
Kind regards.
I bought a Mintor22. I like to know if anyone has had a problem with the engine.
I appreciate your answers
Kind regards.
#6
RE: Any problem with Mintor22
ORIGINAL: Ernie Misner
I think he means we'd like to see what you said in the P.M. for educational purposes.
I think he means we'd like to see what you said in the P.M. for educational purposes.
Ok for what it's worth here it is.
" Okinox, the M22 is a real marvel of engineering and machining and is as beautiful on the inside as it is on the outside. That said, a few of the earlier models were supplied with slightly undersized pistons and rings of questionable quality which caused a low compression problem.
Several complaints from disatisfied customers forced Mintor to take a hard look at their operations and based on their findings they took the decision to suspend all manufacturing and restructure their operations with greater emphasis on processes and Quality Control. If you purchased your engine recently then I believe you have nothing to worry about. Much more information on the Mintor 22 is available from an on going discussion on the F***** **** site, so check it out."
Karol
#11
Senior Member
RE: Any problem with Mintor22
ORIGINAL: Granpooba
Port machining does not appear very quality oriented in my poor eye sight.
Port machining does not appear very quality oriented in my poor eye sight.
BC
#12
Member
Thread Starter
Join Date: Feb 2010
Location: Sabadell, SPAIN
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
RE: Any problem with Mintor22
Concerning the internal engine polished'm a little scared because it's the first time I see a bad cylinder polished.
Could polish better internally what interesting. I think I mention that mechanics do not know much, but my cousin is a mechanic and I'm sick of seeing motors inside.
Not if the shooting refine that.
Well I have been lucky to meet this morning to a shareholder of club buddy Castellar is, this gentleman has been foreman of the Mercedes for several years. He says he has touched 2T racing engines and the same grinding, not to worry.
In the shoot rotating refine shirt.
No problem with the engine running perfect wrath.
No problem with the engine running perfect wrath.
My old boss said if you know of one thing it is best to keep quiet.
Slds.
#13
RE: Any problem with Mintor22
The whole cylinder remarks are funny to say the least. The DL50 ran very well and had one of the worst looking cylinders when it hit the market yet no one complained.
#16
RE: Any problem with Mintor22
ORIGINAL: AJsToyz
The whole cylinder remarks are funny to say the least. The DL50 ran very well and had one of the worst looking cylinders when it hit the market yet no one complained.
The whole cylinder remarks are funny to say the least. The DL50 ran very well and had one of the worst looking cylinders when it hit the market yet no one complained.
#20
Member
Thread Starter
Join Date: Feb 2010
Location: Sabadell, SPAIN
Posts: 36
Likes: 0
Received 0 Likes
on
0 Posts
RE: Any problem with Mintor22
The engine has not rolled. I do not see what the problem according to a good mechanic and have seen them and not spend anything.
#21
RE: Any problem with Mintor22
Nice pictures Capt'n. In the first one it shows nicely the finger or open porting on the two ports opposite from the exhaust. That would give those ports more flow area for sure.
#24
RE: Any problem with Mintor22
Actually the ring had a lot of outward tension. Also a big end gap (a place for compression too leak) and one area of the surface of the ring seemed to be void of contact...maybe caused when the ring was finished up.