Jeti assist reciever
#27
My Feedback: (7)
I have also tried to figure out how I can connect it to CentralBox, using two receivers.
It seems like Assist keeps on providing a stabilised signal to Rx1 even if it has no contact with transmitter, thus preventing secondary receiver connected to Rx2 to kick in. Hope I´m wrong here.......
Egil
It seems like Assist keeps on providing a stabilised signal to Rx1 even if it has no contact with transmitter, thus preventing secondary receiver connected to Rx2 to kick in. Hope I´m wrong here.......
Egil
#28
Well, I got faked out today. Received an email today informing me the Jeti assist receivers were in stock at Esprit only to find out I can't get one until they pass FCC certification for the U.S/Canada. Any idea when that is going to happen?
#30
My Feedback: (7)
Assuming we're talking about an REX7 Assist as opposed to a regular R7 either way will work. Since Rx2 connected to a Central Box will never be used unless Rx1 has almost completely failed I think a regular old R3 for Rx2 is fine. Another option is to connect the REX7A to RX1 and then connect the R3 directly to the REX7A via a PPM link. I believe this configuration will actually provide better antenna diversity and you shouldn't lose stabilization if the secondary receiver actual is put into use.
Last edited by wfield0455; 11-30-2017 at 07:32 AM.
#32
#34
Hi guys,
just received my DS24 with rex7A Rx. Plan to test this out in a foamy. I am new to Jeti, and obviously missing something here.
I have done the basic setup, ATV, subtrim ect. For the gyro setup the manual asks to get into device explorer which shows me the Rex 7A with a tick, when I click on it it shows ERROR Device not recognised. REX7A.bin, line 1.
what am I missing?
Thanks Chatty.
just received my DS24 with rex7A Rx. Plan to test this out in a foamy. I am new to Jeti, and obviously missing something here.
I have done the basic setup, ATV, subtrim ect. For the gyro setup the manual asks to get into device explorer which shows me the Rex 7A with a tick, when I click on it it shows ERROR Device not recognised. REX7A.bin, line 1.
what am I missing?
Thanks Chatty.
#35
My Feedback: (7)
Hi guys,
just received my DS24 with rex7A Rx. Plan to test this out in a foamy. I am new to Jeti, and obviously missing something here.
I have done the basic setup, ATV, subtrim ect. For the gyro setup the manual asks to get into device explorer which shows me the Rex 7A with a tick, when I click on it it shows ERROR Device not recognised. REX7A.bin, line 1.
what am I missing?
Thanks Chatty.
just received my DS24 with rex7A Rx. Plan to test this out in a foamy. I am new to Jeti, and obviously missing something here.
I have done the basic setup, ATV, subtrim ect. For the gyro setup the manual asks to get into device explorer which shows me the Rex 7A with a tick, when I click on it it shows ERROR Device not recognised. REX7A.bin, line 1.
what am I missing?
Thanks Chatty.
#41
If that's successful (will know Monday) we should be done with certification in matter of few weeks.
Zb/Jeti USA
#42
Updates are here:
Jeti Firmware Updates
#44
Hello all,
Does somebody tried REX Assist with CB200 ?
Here is my setup :
TX in Double Path mode
CB200 - V1.27
RX1 : REX6Assist in EX Bus mode - Failasfe disabled - Binded to Primary TX - V1.07
RX2 : RSAT in EX Bus mode - Failsafe disabled - Binded to Secondary TX - V3.25
It seems do not switch to RX2 in Dal Path mode when turned off the primary TX modul : all servos are in Hold and do not respond to TX.
Another feedback ?
Best regards.
Stéphane
Does somebody tried REX Assist with CB200 ?
Here is my setup :
TX in Double Path mode
CB200 - V1.27
RX1 : REX6Assist in EX Bus mode - Failasfe disabled - Binded to Primary TX - V1.07
RX2 : RSAT in EX Bus mode - Failsafe disabled - Binded to Secondary TX - V3.25
It seems do not switch to RX2 in Dal Path mode when turned off the primary TX modul : all servos are in Hold and do not respond to TX.
Another feedback ?
Best regards.
Stéphane
Last edited by Aquilon; 12-02-2017 at 09:36 AM.
#45
My Feedback: (3)
Hello all,
Does somebody tried REX Assist with CB200 ?
Here is my setup :
TX in Double Path mode
CB200 - V1.27
RX1 : REX6Assist in EX Bus mode - Failasfe disabled - Binded to Primary TX - V1.07
RX2 : RSAT in EX Bus mode - Failsafe disabled - Binded to Secondary TX - V3.25
It seems do not switch to RX2 in Dal Path mode when turned off the primary TX modul : all servos are in Hold and do not respond to TX.
Another feedback ?
Best regards.
Stéphane
Does somebody tried REX Assist with CB200 ?
Here is my setup :
TX in Double Path mode
CB200 - V1.27
RX1 : REX6Assist in EX Bus mode - Failasfe disabled - Binded to Primary TX - V1.07
RX2 : RSAT in EX Bus mode - Failsafe disabled - Binded to Secondary TX - V3.25
It seems do not switch to RX2 in Dal Path mode when turned off the primary TX modul : all servos are in Hold and do not respond to TX.
Another feedback ?
Best regards.
Stéphane
https://www.rcgroups.com/forums/show...dates/page2124
#46
#47
My Feedback: (7)
Hello all,
Does somebody tried REX Assist with CB200 ?
Here is my setup :
TX in Double Path mode
CB200 - V1.27
RX1 : REX6Assist in EX Bus mode - Failasfe disabled - Binded to Primary TX - V1.07
RX2 : RSAT in EX Bus mode - Failsafe disabled - Binded to Secondary TX - V3.25
It seems do not switch to RX2 in Dal Path mode when turned off the primary TX modul : all servos are in Hold and do not respond to TX.
Another feedback ?
Best regards.
Stéphane
Does somebody tried REX Assist with CB200 ?
Here is my setup :
TX in Double Path mode
CB200 - V1.27
RX1 : REX6Assist in EX Bus mode - Failasfe disabled - Binded to Primary TX - V1.07
RX2 : RSAT in EX Bus mode - Failsafe disabled - Binded to Secondary TX - V3.25
It seems do not switch to RX2 in Dal Path mode when turned off the primary TX modul : all servos are in Hold and do not respond to TX.
Another feedback ?
Best regards.
Stéphane
You said failsafe is disabled but did you also change Intelligent Failsafe to Assist Off ? If not, try selecting Assist Off instead of Intelligent failsafe. If it still doesn't switch to Rx2 when the primary RF section is disable try turning Ex Bus stabilization off and then see if will switch to secondary when Primary RF section is disabled. It won't act as a gyro with Ex Bus stabilization turned off but will provide useful info. If it switches over to Rx2 properly when EX Bus stabilization is turned off and it doesn't when Ex Bus stabilization is enabled, then there is definitely a bug Ex Bus stabilization over rides fail safe and you'll need to wait for new firmware. Just some thoughts for some things to try if you get a few minutes to do some further testing.
#48
My Feedback: (53)
DC/DS Firmware Update Version 4.23 and 4.24: JETI model s. r. o.
#49
Ttry turning Ex Bus stabilization off and then see if will switch to secondary when Primary RF section is disabled. It won't act as a gyro with Ex Bus stabilization turned off but will provide useful info. If it switches over to Rx2 properly when EX Bus stabilization is turned off and it doesn't when Ex Bus stabilization is enabled, then there is definitely a bug Ex Bus stabilization over rides fail safe and you'll need to wait for new firmware. Just some thoughts for some things to try if you get a few minutes to do some further testing.
Hello Wayne,
So, failsafe is well initiated as follow : Failsafe disabled and Assist Off
New tests today :
Ex stabilization ON : CB doesn't switch to RX2 when TX primary is turned off. Looks like RX1 send "hold" signal to CB200...
Ex stabilization OFF : CB switchs as usual to RX2 when Tx primary is turned off
So, this is the stabilization system that over ride Failsafe, as you mention it...
Waitting for Jeti firmware update !
Best regards.
Stéphane