Nitro models pusher Bobcat?
#428
RE: Nitro models pusher Bobcat?
I asked the UK dealer which is the best one for turbine conversion and he told me to be careful this one is not as strong as the Bobcat, it has an all built up construction rather than a moulded fuselage etc.
#429
Senior Member
My Feedback: (43)
Join Date: Mar 2002
Location: La Luz,
NM
Posts: 618
Likes: 0
Received 0 Likes
on
0 Posts
RE: Nitro models pusher Bobcat?
Mine is finally ready to fly, with OS .91FX and a cut down 14x7 3 blade prop. Needed a bit of lead in the nose to balance at 10". I just mounted a plastic servo box and filled it with shot until balance was right, then added epoxy. I ran the engine and this this is going to scream. I am sure you could exceed the airframe limits fairly easy with this engine. It is very light though. Maiden sunday maybe. Bob
#432
RE: Nitro models pusher Bobcat?
I e-mailed Nitromodels to enquire about the Bobcat & they told me they do not ship internationaly.
How do you guys outside the US get one?
Is there a UK dealer?
Edit:- Just found an earlier post www.Raidentech.com
This company ship international. Unfortunately they are out of stock at present.
Regards
Jim
How do you guys outside the US get one?
Is there a UK dealer?
Edit:- Just found an earlier post www.Raidentech.com
This company ship international. Unfortunately they are out of stock at present.
Regards
Jim
#433
RE: Nitro models pusher Bobcat?
Jascat 100
UK Dealer
How do you guys outside the US get one?
Is there a UK dealer?
UK Dealer
http://www.wholesaleplanes.co.uk
Regards
The Bush
UK Dealer
How do you guys outside the US get one?
Is there a UK dealer?
UK Dealer
http://www.wholesaleplanes.co.uk
Regards
The Bush
#435
Member
My Feedback: (38)
Join Date: Nov 2004
Location: cherokee,
NC
Posts: 30
Likes: 0
Received 0 Likes
on
0 Posts
RE: Nitro models pusher Bobcat?
i had a thunder tiger .91 with a pipe on mine. it flew nice but did not seem to fly the way i thought a jet should. i figured out how to put my .81 rossi ducted fan motor with the pipe on it and now it flys realllllly fast. this engine comes with an onboard needle valve and fine tuning is a snap. it uses more gas than the tiger so the flight ended prematurely and i had a crash landing in the corn field. while repairs were in progress (just a little balsa on the leading edge of the right wing) i bent some 5/32 piano wire to see if i could reinforce the landing gear. can't wait to get back to the field.
#437
Banned
Join Date: Mar 2003
Location: Tokoroa, , NEW ZEALAND
Posts: 3,848
Likes: 0
Received 0 Likes
on
0 Posts
RE: Nitro models pusher Bobcat?
ORIGINAL: Jascat100
Edit:- Just found an earlier post www.Raidentech.com
This company ship international. Unfortunately they are out of stock at present.
Edit:- Just found an earlier post www.Raidentech.com
This company ship international. Unfortunately they are out of stock at present.
#438
My Feedback: (102)
RE: Nitro models pusher Bobcat?
ORIGINAL: m2energysolutions
Hi,
Anyone got a byron fan shroud that they want to get rid of cheap?
Thanks!
Dave
Hi,
Anyone got a byron fan shroud that they want to get rid of cheap?
Thanks!
Dave
Tommy
#439
Senior Member
RE: Nitro models pusher Bobcat?
ORIGINAL: Jascat100
I e-mailed Nitromodels to enquire about the Bobcat & they told me they do not ship internationaly.
How do you guys outside the US get one?
Is there a UK dealer?
Edit:- Just found an earlier post www.Raidentech.com
This company ship international. Unfortunately they are out of stock at present.
Regards
Jim
I e-mailed Nitromodels to enquire about the Bobcat & they told me they do not ship internationaly.
How do you guys outside the US get one?
Is there a UK dealer?
Edit:- Just found an earlier post www.Raidentech.com
This company ship international. Unfortunately they are out of stock at present.
Regards
Jim
Even the dealer in Denmark are selling for only £120........................Just noticed that the UK dealer has it for £169.99 ($306) plus shipping.[]
I asked Raidentech about shipping and got the reply "due to the post office's International shipping size limit, we can not ship out the item to your country"[][]
Greg
#440
Senior Member
RE: Nitro models pusher Bobcat?
How about an even smaller Bobcat lookalike
http://www.hobby-lobby.com/vdiamond.htm
Review
http://www.rcg****s.com/forums/showthread.php?t=554872
International shipping not a problem
Greg
http://www.hobby-lobby.com/vdiamond.htm
Review
http://www.rcg****s.com/forums/showthread.php?t=554872
International shipping not a problem
Greg
#441
My Feedback: (4)
Join Date: Dec 2001
Location: Prattville,
AL
Posts: 418
Likes: 0
Received 0 Likes
on
0 Posts
RE: Nitro models pusher Bobcat?
knowcrash
Your right about the .81 Rossi ducted fan motor 2 of them have put me down.
One lost a rod the other broke the crank off in flight.
Has any one ever heard of such?
I have been buying them up lately because their selling dirt cheep.
I am working a bid on one now but I am hoping it will not go thought.
In Hine site I could have bought a new os 91 ducted fan motor by now.
Johnny
Your right about the .81 Rossi ducted fan motor 2 of them have put me down.
One lost a rod the other broke the crank off in flight.
Has any one ever heard of such?
I have been buying them up lately because their selling dirt cheep.
I am working a bid on one now but I am hoping it will not go thought.
In Hine site I could have bought a new os 91 ducted fan motor by now.
Johnny
#443
My Feedback: (2)
Join Date: Apr 2002
Location: Strathcona county,
AB, CANADA
Posts: 5,394
Received 0 Likes
on
0 Posts
RE: Nitro models pusher Bobcat?
Funny they can ship from China to California, but can't go any further .....[sm=drowning.gif]
The shipping box measures 43" x 16.5" x 8.5" . There are lots of ways of shipping a box that size...just depends on how much you are prepared to pay. I'd suggest finding someone in the US that would be willing to take delivery of it for you, and turn around and ship it to you.
The shipping box measures 43" x 16.5" x 8.5" . There are lots of ways of shipping a box that size...just depends on how much you are prepared to pay. I'd suggest finding someone in the US that would be willing to take delivery of it for you, and turn around and ship it to you.
#445
Senior Member
Join Date: Jun 2004
Location: Charleston,
SC
Posts: 143
Likes: 0
Received 0 Likes
on
0 Posts
RE: Nitro models pusher Bobcat?
Have one under construction. First thing I did was to get rid of that ugly green stripe on the nose and replace it with a red one (rustoleum matched the red canopy trim).
I have been debating motor options in my head. I'm a firm believer in light is better.
Retracts, while cool and speedy are extra weight and add reliability issues. Never mind the extra cost.
I have put large 2 strokes on small planes and the results (aside from thick winged 3d designs with 4stroke motors) have been unlimited vertical and poor low speed handling (due to the added weight of the bigger motor). More power does not appear to mean more speed. At least in the cases I have encountered.
For the price you can't beat the OS 46ax for power/weight. I was all set to buy it when I read about the OS 55ax. One ounce more weight then the 46 and 15% more power with the same mounting dimentions. There are better and more pwoerful motors to be had, but I am not looking for ultimate speed (and empty wallet), just a go fast fun flying cool looking jet wannabe.
I'll let you all know how it runs and flys.
I have been debating motor options in my head. I'm a firm believer in light is better.
Retracts, while cool and speedy are extra weight and add reliability issues. Never mind the extra cost.
I have put large 2 strokes on small planes and the results (aside from thick winged 3d designs with 4stroke motors) have been unlimited vertical and poor low speed handling (due to the added weight of the bigger motor). More power does not appear to mean more speed. At least in the cases I have encountered.
For the price you can't beat the OS 46ax for power/weight. I was all set to buy it when I read about the OS 55ax. One ounce more weight then the 46 and 15% more power with the same mounting dimentions. There are better and more pwoerful motors to be had, but I am not looking for ultimate speed (and empty wallet), just a go fast fun flying cool looking jet wannabe.
I'll let you all know how it runs and flys.
#446
Member
Join Date: Dec 2005
Location: Sydney, AUSTRALIA
Posts: 55
Likes: 0
Received 0 Likes
on
0 Posts
RE: Nitro models pusher Bobcat?
I aggree, I have flown mine about 2 dozen times now and am more than happy with the TT46 Pro I fitted, so much so that I bought a brand new one after the first weekend out and fitted it in. After running in, I put on a APC 9 x 6 and the performance is fantastic.
I had a TT 61 Pro but to fit this would bring the wing loading up from 23 OZ to 29 OZ, I dont like trying to glide bricks if you get a dead stick, I am trying to work out how to lose some of the 5 OZ I have in the nose to make it lighter.
The possible solution arrived today, a brand new OS RSP pylon motor, lighter more HP and 24000 RPM, I am going to bring the header thru the fuse and mount the pipe underneath to better streamline the model as well as mold up some servo covers for the ailerons and rudder servos to cut down drag.
I would even like to build a balsa built up 2/3rds size and fit it up with a OS 21 marine motor (30000 RPM) and fit a wemotec 90 mm fan.
I had a TT 61 Pro but to fit this would bring the wing loading up from 23 OZ to 29 OZ, I dont like trying to glide bricks if you get a dead stick, I am trying to work out how to lose some of the 5 OZ I have in the nose to make it lighter.
The possible solution arrived today, a brand new OS RSP pylon motor, lighter more HP and 24000 RPM, I am going to bring the header thru the fuse and mount the pipe underneath to better streamline the model as well as mold up some servo covers for the ailerons and rudder servos to cut down drag.
I would even like to build a balsa built up 2/3rds size and fit it up with a OS 21 marine motor (30000 RPM) and fit a wemotec 90 mm fan.
#448
RE: Nitro models pusher Bobcat?
Got this email from another uk agent:
"Hi mate,
Just for your information, the first UK dealer to have the Bobcat (back in September) was www.planenutz.co.uk who still have plenty in stock at £165. RCM&E will be reviewing it shortly for Plane Nutz Ltd.
Pete"
Regards
The Bush
"Hi mate,
Just for your information, the first UK dealer to have the Bobcat (back in September) was www.planenutz.co.uk who still have plenty in stock at £165. RCM&E will be reviewing it shortly for Plane Nutz Ltd.
Pete"
Regards
The Bush
#449
RE: Nitro models pusher Bobcat?
I have ordered 2 direct from the manufacturer in China.
$85 each + $220 express mail service for the 2.
Works out at £102 each.
Regards
Jim
$85 each + $220 express mail service for the 2.
Works out at £102 each.
Regards
Jim