Scanner Servos -- has anyone tried them???
#1
Thread Starter
Join Date: Jul 2002
Location: Tacoma,
WA
Posts: 5,037
Likes: 0
Received 0 Likes
on
0 Posts
Scanner Servos -- has anyone tried them???
Greetings, take a look at the Scanner brand of servos from Hobby Lobby. http://www.hobby-lobby.com/servos.htm
Has anyone tried them?
Thanks,
Ernie
Has anyone tried them?
Thanks,
Ernie
#2
Banned
Join Date: Mar 2003
Location: Tokoroa, , NEW ZEALAND
Posts: 3,848
Likes: 0
Received 0 Likes
on
0 Posts
RE: Scanner Servos -- has anyone tried them???
I've tried a few and they seem fine -- although you'll note that HobbyCity/United Hobbies has them a *lot* cheaper than HobbyLobby.
#3
Junior Member
Join Date: Dec 2007
Location: ShenZhen, CHINA
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
RE: Scanner Servos -- has anyone tried them???
Try this one,high performance with low price.
http://www.flyermate.com/flyermate_d55_servo.php
http://www.flyermate.com/flyermate_d55_servo.php
#4
Thread Starter
Join Date: Jul 2002
Location: Tacoma,
WA
Posts: 5,037
Likes: 0
Received 0 Likes
on
0 Posts
RE: Scanner Servos -- has anyone tried them???
Thanks XJet. I did notice that Tower's price on the HiTec's was much better also.
Any clue if the Scanner servos are the "same as anything else"?
Thanks again,
Ernie
Any clue if the Scanner servos are the "same as anything else"?
Thanks again,
Ernie
#5
Senior Member
My Feedback: (4)
Join Date: Oct 2007
Location: St. Louis,
MO
Posts: 1,320
Likes: 0
Received 0 Likes
on
0 Posts
RE: Scanner Servos -- has anyone tried them???
I have some on a Lanier edge 540 87" Haven't flown them yet but they seem fine so far... I have video of them on the rcu videos
#7
Senior Member
Join Date: Jan 2007
Location: baton rouge,
LA
Posts: 442
Likes: 0
Received 0 Likes
on
0 Posts
RE: Scanner Servos -- has anyone tried them???
Troy built models has the best prices on hitec's that i have found. 5645's for 45$, 5985's for 75$, and 5955's for 90$
#8
Senior Member
My Feedback: (4)
Join Date: Oct 2007
Location: St. Louis,
MO
Posts: 1,320
Likes: 0
Received 0 Likes
on
0 Posts
RE: Scanner Servos -- has anyone tried them???
I got them from Hobby City for 16.95 I also got the same ones from Abell RC for around 22.00 bucks there the 132 oz MG ones Hopefully they will hold up. did you check out the Vid?
#9
Senior Member
Join Date: Jun 2005
Location: Bullard,
TX
Posts: 160
Likes: 0
Received 0 Likes
on
0 Posts
RE: Scanner Servos -- has anyone tried them???
Is it my imagination, or has United Hobby raised the price of shipping?
I put together an order consisting of a doz 9" props and a few small items and the cheapest freight was $20. Needless to say, I flushed the order. All of my previous orders have been much larger and heavier, but the shipping has never been over $12.
I have been very pleased with the service and products from United, but if this shipping cost is now correct, I don't think I can continue with them.
I put together an order consisting of a doz 9" props and a few small items and the cheapest freight was $20. Needless to say, I flushed the order. All of my previous orders have been much larger and heavier, but the shipping has never been over $12.
I have been very pleased with the service and products from United, but if this shipping cost is now correct, I don't think I can continue with them.
#10
Senior Member
My Feedback: (4)
Join Date: Oct 2007
Location: St. Louis,
MO
Posts: 1,320
Likes: 0
Received 0 Likes
on
0 Posts
RE: Scanner Servos -- has anyone tried them???
Yeah, its a little bit more money to ship from over there, I try to always buy bulk or else it evens out with higher priced stuff in the long run... They have a USA warehouse that is opening up soon so shipping should be alot cheaper... u can veiw it from there home page it talks about it somewhere on there.