RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: angturbines
Showing results 1 to 23 of 23
Search took 0.59 seconds.
Forum: JetCat Turbine Direct Support
05-17-2007, 02:51 PM
Replies: 6
Views: 1,203
Posted By angturbines

RE: P-80 puffing on Idle

Hi,
This puffing sound can be due to an excess of oil to the bearings, once the oil has passed through the bearings/shaft tunnel it finds its way out at the back of the turbine and is burnt in the...
Forum: Aerodynamics
01-21-2007, 01:24 PM
Replies: 72
Views: 7,201
Posted By angturbines

RE: WHAT DID I MISS - Jet Engine Question?

for evry action there is an equal but oposit reaction.
Forum: JetCat Turbine Direct Support
12-08-2006, 04:42 AM
Replies: 31
Views: 8,860
Posted By angturbines

RE: TCW3 Oil

Any properties that Aroshell or tcw3 oils have are long gone when we dilute the oil with fuel. I have been building and using jet engines for years and have found that any light oil will work fine,...
Forum: JetCat Turbine Direct Support
11-27-2006, 02:14 AM
Replies: 12
Views: 2,359
Posted By angturbines

RE: PowerFail problem

what oil and mix are you using?
Forum: JetCat Turbine Direct Support
11-23-2006, 01:03 PM
Replies: 8
Views: 1,989
Posted By angturbines

RE: P80 RPM settings

Hi Mat,
Lowidle is now setup and works a treat,I can now land with the engine at 30,000 rpm, that 5k has made quite a difference to the landing thrust.
regards Andy.
Forum: JetCat Turbine Direct Support
11-21-2006, 01:27 PM
Replies: 8
Views: 1,989
Posted By angturbines

RE: P80 RPM settings

Hi, no I was wating for you to get back to me with info from Germany, I have had a look into the ECU using the GSU, and I can't alter the lower rpm setting lower than 35K, but there is a menue for...
Forum: JetCat Turbine Direct Support
11-16-2006, 12:47 PM
Replies: 8
Views: 1,989
Posted By angturbines

RE: P80 RPM settings

Hi , The software is version 5, the engine is only 6 weeks old. I have not tried to lower the rpm yet as I was waiting for any information on a safe lower RPM.
thanks Andy.
Forum: JetCat Turbine Direct Support
11-13-2006, 04:50 AM
Replies: 8
Views: 1,989
Posted By angturbines

P80 RPM settings

Hi, what is the lowest RPM the engine can be safely set to without over temping when accelerated.
I find that 35k is still pushing my Harpoon along the tarmac and a lower thrust at idle would be...
Forum: JetCat Turbine Direct Support
10-13-2006, 11:24 AM
Replies: 7
Views: 1,852
Posted By angturbines

New P80

I have just had a new p80 , on looking at the max RPM it is set to 123K , is this setting ok,I thought it should max out at 117K , if this setting is OK what sort of thrust are the new engines giving?
Forum: RC Jets
05-29-2006, 02:04 PM
Replies: 3,661
Views: 626,219
Posted By angturbines

RE: JetJoe OWNERS thread

Hi All,
Looking at the pics of the chamber is the mk1 type, the sticks are not inconel, the later combusters have straight sticks and are inconel.
regards Andy.
Forum: RC Jets
07-27-2005, 03:47 AM
Replies: 3,661
Views: 626,219
Posted By angturbines

RE: JetJoe OWNERS thread

Hi All,
I think you have your lines crossed,as you will see on the JJ web site Andy at Anglesey Turbines is the UK agent for JJ.
Please contact me for further information on sales and...
Forum: RC Jets
06-30-2005, 11:13 AM
Replies: 3,661
Views: 626,219
Posted By angturbines

RE: JetJoe OWNERS thread

Hi All,
The problem with the rpm sensor's is a small surface mount capacitor mounted directly under the cable tie, if to much pressure has been applied it can damage the capacitor.This can easily...
Forum: RC Jets
05-10-2005, 09:28 AM
Replies: 3,661
Views: 626,219
Posted By angturbines

RE: JetJoe OWNERS thread

Hi All,
The o ring is not to dampen the for and aft movement so much as to stop the outer cage rotating, the bearing should have a nice sliding fit in the tunnel and should not be tight,lf any...
Forum: RC Jets
05-07-2005, 06:07 PM
Replies: 3,661
Views: 626,219
Posted By angturbines

RE: JetJoe OWNERS thread

Hi All,
The cc is located on the NGV but not a tight fit , the only real means of keeping the cc in the correct position is with the plug. If the fuel and gas lines are not quite set in the...
Forum: RC Jets
05-05-2005, 07:28 PM
Replies: 3,661
Views: 626,219
Posted By angturbines

RE: JetJoe OWNERS thread

Hi,
If the spark erosion fails and you require a new NGV I have them in stock, or you could rotate the NGV in the casing and re-drill and tap a fresh set to holes.
Forum: RC Jets
05-04-2005, 10:37 PM
Replies: 3,661
Views: 626,219
Posted By angturbines

RE: JetJoe OWNERS thread

Sounds like the pump or the battery pack, the original JJ pumps have been known to give problems,Have a look at the power reading on the FADEC,
Forum: RC Jets
05-02-2005, 09:35 AM
Replies: 114
Views: 8,752
Posted By angturbines

RE: WOW JETJOE FIRST UK REP BECOMES NEW UK REP

Thanks .
Forum: RC Jets
05-02-2005, 04:14 AM
Replies: 114
Views: 8,752
Posted By angturbines

RE: WOW JETJOE FIRST UK REP BECOMES NEW UK REP

My mail address used for anything to do with JJ is as on the JJ web site. This mail address is one that I have had for over 5 years and do not use other than for private mail, and have not offered ...
Forum: RC Jets
05-01-2005, 12:47 PM
Replies: 114
Views: 8,752
Posted By angturbines

RE: WOW JETJOE FIRST UK REP BECOMES NEW UK REP

Hi All , In reply to Treadstone21 question,

Has Joe appointed you to this position ? Yes if you look JJon the web site you will see my name.

Do you have any JJ in stock to sell ? Yes always...
Forum: RC Jets
12-29-2004, 12:32 PM
Replies: 35
Views: 4,671
Posted By angturbines

RE: WHAT IS THE RIGHT WAY TO END A FIRE IN A JET?

I recently stripped an engine that had been in an aircraft with a fire and was put out with dry powder, the bearings were totally shot,Always use CO2 in short bursts ,the CO2 will then worm up to a...
Forum: RC Jets
09-24-2004, 02:54 AM
Replies: 170
Views: 17,943
Posted By angturbines

RE: JetJoe engines

Have you had it running it with the tail cone off,what are the temps like then, may just be the cone outlet dia to small.
Forum: RC Jets
09-13-2004, 01:14 PM
Replies: 35
Views: 3,056
Posted By angturbines

RE: bae hawk eats the tarmac

not a bad day on Sat , but cr-p on Sunday.
andy
Forum: RC Jets
09-13-2004, 01:12 PM
Replies: 35
Views: 3,056
Posted By angturbines

RE: bae hawk eats the tarmac

Yes it was
Showing results 1 to 23 of 23


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.