RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: charleyrc
Showing results 1 to 10 of 10
Search took 0.65 seconds.
Forum: Glow Engines
09-30-2006, 07:48 PM
Replies: 8
Views: 1,109
Posted By charleyrc

RE: Saito 150 Help

The reason the prop nut won't go all the way down without the backplate is because it is a prop nut/shaft used to hold the true turn spinner on. I didn't have a reqular prop nut to put on it at the...
Forum: Glow Engines
09-30-2006, 06:24 PM
Replies: 8
Views: 1,109
Posted By charleyrc

RE: Saito 150 Help

Update to Vibration Problem

I took the plane out today and tried it without the spinner on, just the back plate because my prop nut wouldn't screw down far enough without it. The propnut has a...
Forum: Glow Engines
09-30-2006, 11:53 AM
Replies: 8
Views: 1,109
Posted By charleyrc

Saito 150 Help

I have new to me Saito 150. It seems to me that it runs way too rough at high RPM. So rough that you cannot adjust the high speed needle at full throttle. At idle it seams OK. Here are the facts:
...
Forum: WildHare R/C Support
09-27-2005, 12:14 PM
Replies: 102
Views: 6,709
Posted By charleyrc

RE: Design Contest entries. Post 'em here for all to see.

I think all the entries are good. But I must say that I am partial to the Red white and Blue patriotic style from dntmn. Maybe it's a sign of the times are but it just looks great. At a recent IMAC...
Forum: 3D Electric Flying!
09-21-2005, 01:06 PM
Replies: 7
Views: 10,338
Posted By charleyrc

RE: Plans for Hydro foam

Ok guys,

Like most of you Mikes design and video has got me trembling with anticipation!! This looks like the most fun a guy can have with his clothes on. I ran across this link that claims to...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
09-28-2004, 09:04 PM
Replies: 10
Views: 995
Posted By charleyrc

RE: Dumb Transmitter Battery Question

Ooops, my bad,

The 9C does not have a diode that can be jumped. If you looked at the links I posted for you then you will see that. But the page does show others that can be jumpered. Perhaps...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
09-28-2004, 09:01 PM
Replies: 4
Views: 596
Posted By charleyrc

RE: Reciver Antenna Cut

I didn't expect such a quick reply. Thanks for the advice.
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
09-28-2004, 08:57 PM
Replies: 10
Views: 995
Posted By charleyrc

RE: Dumb Transmitter Battery Question

There is another way. If you can do some tedious soldering then go to the link below. It show's how to jumper the diode that prevents you from using a fast charger or cycling you battery while still...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
09-28-2004, 08:28 PM
Replies: 3
Views: 660
Posted By charleyrc

Metal Spring at end of antenna???

I've been reading posts about receiver problems and noticed that some people with problems mentioned using rubber bands to hold their antennas to the tail. I have been using the same method for years...
Forum: RC Radios, Transmitters, Receivers, Servos, gyros
09-28-2004, 08:00 PM
Replies: 4
Views: 596
Posted By charleyrc

Reciver Antenna Cut

I was removing a known good receiver from an airplane and accidentally cut approx 3 inches off the end. Range check on the ground seem fine but I am just not sure. Can I re-attach (solder) the broken...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.