RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: DesertHucker
Showing results 1 to 17 of 17
Search took 0.14 seconds.
Forum: 3D Flying!
10-08-2005, 09:46 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

have you flown this plane yet with the sig tail wheel?

I tried a similar setup.
The tail was to high of the ground and i could not get rotation of the ground the faster it whent down the...
Forum: 3D Flying!
10-08-2005, 09:20 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

should be fun with the YS 110 up front.
Looking at pulling out the saito 100 and replacing it with YS110 tuns more grunt
Forum: 3D Flying!
10-07-2005, 09:46 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

i would not cut the wing tubes.
unless you are willing to loose the plane to the un-known
Forum: 3D Flying!
10-07-2005, 12:28 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

Only takes about 30 minutes to do the tail wires. I dont know why it is taking everyone so long to do them.
They dont have to be don that tite that it buckles everything.
Leave them loose do up...
Forum: 3D Flying!
09-23-2005, 04:08 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

I have my tank back on the CG and use a cline on the saito 100 inverted runs well no change untill no fuel left
Forum: 3D Flying!
09-20-2005, 10:03 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

I agree with dyehard the wing bolts are not a problem most of the flyers at our club have cut them down they are long.
The canopy bolts will come loose i took the metal ones out and put sone ply...
Forum: 3D Flying!
09-08-2005, 08:12 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

who is yogi149?
what does he need this info for?
what is AFPD?
Forum: 3D Flying!
09-05-2005, 10:10 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

if you were able to wiegh 2 h90 with no gear installed you would be surprised of the differant wieghts i have done this and mine is 3/4lb more than the other one
Forum: 3D Flying!
08-18-2005, 07:13 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

tianci you using saito 100.
My friend has a os120 4s in his prophangs lot better than mine.
I find it only just pulls out with the saito 100. if you watch the top flyers they are continualy...
Forum: 3D Flying!
08-18-2005, 06:57 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

Hi Tianci,
H3D is a great plane even at a dead stick.
But i was flying high one time lot of wind gusts 35knts dived like a dive bomber to get her on the ground before it got blown away hart in...
Forum: 3D Flying!
08-18-2005, 06:48 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

Have a read through this site http://www.saitoengines.com/ i think all your problem is tuning and the correct amount of nitro to suit the plug you are using.
Knocking can be the same as pining in...
Forum: 3D Flying!
08-17-2005, 09:10 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

but i think maybe Aim's problem sounds like not run in or wrong plug a short reach type like an OS8 what is the H9 3011 short or long
Forum: 3D Flying!
08-17-2005, 09:07 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

I use the OS f plug with no trouble great starting good idle and trnsition.
i set the top end with a tacho 200 rpm under peak then the bottom end lean it until it stumbles at transition then...
Forum: 3D Flying!
08-17-2005, 04:44 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

Aim are you using an OS Fplug.
I had to run mine for the first 40 minutes the rite side up then installed it normaly.
Run it and keep leaning it as the instructions say im sure it should only be...
Forum: 3D Flying!
08-16-2005, 05:03 AM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

none needed on either of mine
Forum: 3D Flying!
08-08-2005, 06:29 PM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

I am at 1/2 mile high with a saito 100 15% nitro hovers at 85% throttle slow to pullout whant to get a YS110 to replace it
Forum: 3D Flying!
05-08-2005, 01:19 PM
Replies: 881
Views: 104,606
Posted By DesertHucker

RE: SEAGULL HARRIER 90...WHO'S GOT ONE?

I balanced mine with out the battery installed.
put the plan on the balancer upside down at the wanted CG then set the battery along the fuse untill you find the balance point then install the...
Showing results 1 to 17 of 17


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.