RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: raptor30se
Showing results 1 to 10 of 10
Search took 0.05 seconds.
Forum: RC Jets
07-15-2014, 09:12 AM
Replies: 309
Views: 103,346
Posted By raptor30se

Bought the last one at KY Jets this year, had...

Bought the last one at KY Jets this year, had Todd bring it up on the trailer to negate the shipping on this large box. Thanks again!
Forum: RC Jets
08-15-2013, 06:07 AM
Replies: 309
Views: 103,346
Posted By raptor30se

Thanks for that info, I was more curious to if...

Thanks for that info, I was more curious to if you had the gear extended when balancing the plane?
Forum: RC Jets
08-13-2013, 10:13 AM
Replies: 309
Views: 103,346
Posted By raptor30se

I had balance mine with the gear up, if I balance...

I had balance mine with the gear up, if I balance with the gear down I could get rid of 2oz of the nose, I just wanted to be safe first flight. Assume it is supposed to be balance with the gear down...
Forum: RC Jets
08-11-2013, 04:14 PM
Replies: 309
Views: 103,346
Posted By raptor30se

I flew it just as is, didn't do anything to...

I flew it just as is, didn't do anything to sleeve it. No problem so far.
Forum: RC Jets
08-08-2013, 06:35 AM
Replies: 309
Views: 103,346
Posted By raptor30se

Maidened mine over the weekend, nice flying jet. ...

Maidened mine over the weekend, nice flying jet. I am enjoying it. Video attached, cameraman missed the landing though. I am using a Jets Munt VT80 with dreamworks all electric retract brake setup...
Forum: RC Jets
07-25-2013, 05:43 AM
Replies: 309
Views: 103,346
Posted By raptor30se

RE: Shulman Aviation Turbinator ARF

On my wing I had to cut out the fiberglass sleeves that were in all the wing bolt hold holes to relieve them alittle as to align the bolts so they would thread into the blind nuts to hold down the...
Forum: RC Jets
05-23-2013, 09:56 AM
Replies: 309
Views: 103,346
Posted By raptor30se

RE: Shulman Aviation Turbinator ARF

That's exactly what he is saying.
Forum: RC Jets
05-23-2013, 09:55 AM
Replies: 309
Views: 103,346
Posted By raptor30se

RE: Shulman Aviation Turbinator ARF

Makes perfect sense now. I do appreciate your explanation. I am an assembler not a builder :D. One more question, is 1/8" down elevator good starting point for landing flap mix?

Thanks in...
Forum: RC Jets
05-21-2013, 02:05 PM
Replies: 309
Views: 103,346
Posted By raptor30se

RE: Shulman Aviation Turbinator ARF

Thanks Chis -

Little confused on CG the wing I get the same measurement when at the center of the wing vs where the wing meets the scoop. The wing doesn't start to sweep back till after the...
Forum: RC Jets
05-20-2013, 05:41 PM
Replies: 309
Views: 103,346
Posted By raptor30se

RE: Shulman Aviation Turbinator ARF

Are the manual setting for flaps a good starting point at 1" takeoff and 2.5" for landing? Also how much down elevator mix is needed for each of those settings? Getting ready to maiden mine very...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.