RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: headhunter23
Showing results 1 to 20 of 20
Search took 0.10 seconds.
Forum: Speed - Electric
12-09-2009, 06:11 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial

I tried actually separating the top and bottom. No workie, tried with acetone etc, cracked bottom hull a bit. Cutting hatch is so far the only way that keeps the strength of the boat together and...
Forum: Speed - Electric
12-07-2009, 04:08 AM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial

Are you talking about the hot glue? Cold seemed to work for me.
Forum: Speed - Electric
10-25-2009, 09:13 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial

Ur right dragon.;)

Jet bash and everyone else running in the fall, these things will suck up leaves and they will also get stuck on grates reducing or all together losing prime! Check once in a...
Forum: Speed - Electric
10-24-2009, 08:04 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial

The only boats I had seen with larger or oversize was... mini-v with... 28 or 29mm drive, thing apparently sunk due to over weight and no foam. Ahhh... there was another, someone stuck in a 33mm...
Forum: Speed - Electric
10-18-2009, 07:24 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial

Wrangle boy, I've tried the 5 min epoxy, no good, chips when hit. Did that with some automotive stuff too, same problem. You want something that holds yet has a bit of flex due to the hits you will...
Forum: Speed - Electric
10-09-2009, 02:19 AM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial

Just like quicksilver now... always lurking but theres so many people to answer stuff...[:-]
Forum: Speed - Electric
10-07-2009, 07:00 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial

Demon if they are new packs you have very little chance of anything occurring, i've got... geez dozens o lipo's no fires and all of them dunked or wet. I've found no matter what, you always seem to...
Forum: Speed - Electric
06-12-2009, 11:39 AM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial

sundogz don;t forget to reglue the exhuast pipes on the top, mine leaked, did em up with shoe goo, was never an issue. Also a bead around the neck joint is good too.

Ivan.
Forum: Speed - Electric
04-20-2009, 09:12 AM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

Man that's nice that it reprimes with no letting off throttle at all!:D Might have to look at my bigger jet boat, see if something similar can be done.
Forum: Speed - Electric
04-17-2009, 09:58 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

dude buy the ebay ndq fake jet sprint, it is literly the cheapest best way to jet boat, just swap motor n servo n batt with something from 2000's!;) Any other hulls are completely hit or miss. ...
Forum: Speed - Electric
02-25-2009, 09:31 AM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

Vague memory but i think it was 2.3mm shaft.
Forum: Speed - Electric
02-24-2009, 06:34 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

I think the props are same size(graupner mini jet vs knock off), shaft size for knock off is smaller though for sure.

Ivan.
Forum: Speed - Electric
01-08-2009, 12:59 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

Quicker and cheaper would be to get prop from hobby store and throw on high speed drill or lathe, then put a file to it till it's the size you need. Take your time. If your doing an octura, make...
Forum: Speed - Electric
11-17-2008, 11:25 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

You can use any servo you want, my buddy swears by the big heavy servo, me I go with a small light 5gram servo. For mount, just get a small piece of aluminum angle, notch out where servo sits.

...
Forum: Speed - Electric
10-25-2008, 05:32 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

Dam you have a pick of your intake? Maybe some pics inside too? What kind of water are you running?
Forum: Speed - Electric
10-01-2008, 01:12 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

If your testing jets, make a little dounut shaped tub, mount jet against cheap weight measuring stuff, fill tub run jet measure. Would be easiest way to screw around and test. But if you really...
Forum: Speed - Electric
09-30-2008, 06:17 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

Keep putting more power to it, no change is *****g it out. Nice numbers, was wondering what it pulled without grate. Big difference.

Ivan.
Forum: Speed - Electric
09-30-2008, 12:42 AM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

Not sure if ya read it but dragon and a couple guys made custom smaller exhaust jets to get increased acceleration and cornering. not sure if it helped top end. The drives do max out, I've maxed...
Forum: Speed - Electric
09-29-2008, 10:20 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

hope it's the geko... too much weight with real gps, I had run a boat beside knock off, approximately 20-25kph, more speed available without grate.
Forum: Speed - Electric
09-29-2008, 12:08 PM
Replies: 3,285
Views: 607,120
Posted By headhunter23

RE: Unofficial "NQD" Tear into Jetboat Thread

Hey dam, the drive ya replaced is pretty much an exact duplicate of the mini graupner, only improved upon in terms of minor differences... although I can't remember the graupner is sleeved... I don't...
Showing results 1 to 20 of 20


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.