RCU Forums - Search Results

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Community
Search
Notices
 
Search: Posts Made By: MHall
Showing results 1 to 25 of 433
Search took 1.31 seconds.
Replies: 8
Views: 797
Posted By MHall

RE: Slash broken...finally...

Yes, he is running an adaptor from the stock Traxxas plug to an Tamiya end. Guess he has some older batteries that he runs....
Replies: 2
Views: 401
Posted By MHall

RE: radio signal question

You have something wrong with your system. The RX does not know what position it is in, so flipping up side down has nothing to do with it. It seem to me that it is flipping over because the RX is...
Replies: 8
Views: 481
Posted By MHall

RE: I have a problem with my R/C Truck!

I hate to suggest a stupid idea but the truck looks to be on the cheaper end of the scale and there for QC is not that great. Have you checked that the whole system is wired correctly?? Make sure...
Replies: 3,214
Views: 432,311
Posted By MHall

RE: The Official Traxxas Slash short-course race truck

I am sure that there are lots of guys who could answer your questions but we need to know a few things to give you a better answer. Where you run it, what do you do with it, what kind of money do you...
Replies: 6
Views: 483
Posted By MHall

RE: ummm help?

This is a very good rule to follow but not always nessasary. I have a Intellect 6 cell 3600 pack that says to charge at 6 amps! I use it for racing and slam 6 amps into it all the time and it keeps...
Replies: 9
Views: 573
Posted By MHall

RE: slash motor and other ?'s

I am not sure about yours, but mine came out of the box with the slow gearing (18/86). I have been racing mine since it was fresh out of the box. The motor has never over heated. I switched my pinion...
Replies: 7
Views: 1,294
Posted By MHall

RE: Anyone build wooden obstacles for a street course?

A friend of mine and I have built 3 table tops for our road track. Everybody loves them, but watch out for the bigger jump!! There are several pic's of them at-...
Replies: 45
Views: 3,276
Posted By MHall

Replies: 4
Views: 750
Posted By MHall

RE: Suspension sluggish...help...

Shock oil in a R/C shock only provides dampining of piston movement not ride height. If the shock(s) is dry then the seals would stick to the shafts or if the oil has turned to a sludge then oil...
Replies: 4
Views: 750
Posted By MHall

RE: Suspension sluggish...help...

Just a thought, how old are the seals?? If they are getting old and hard then they are not sliding on the shafts smoothly any more.
Replies: 1
Views: 394
Posted By MHall

Camber angles

Trying to set up the front end of my truck that I race on a road course and wanted to know what kind of camber angles that are used on various types of buggy's, cars, and trucks for road courses. I...
Replies: 8
Views: 727
Posted By MHall

RE: My slash with winter setup

That thing looks sweet! What did you use for the ice spikes? How does it do in soft powder?
Replies: 2
Views: 432
Posted By MHall

RE: Slash Racing in Sacramento, California

I hope this is ok to post,

Speedworld Raceway
90 Corporation Yard Rd.
Roseville, Ca. 95678
Phone: 783-8864
speedworld.rcracing.com

The next race is Dec. 12. I think the race...
Replies: 9
Views: 509
Posted By MHall

RE: Slash Racing

We have a blast racing our Slash's at Speedworld Raceway in Roseville Ca. The races are every other Friday night. It is a road course that we add over 12 small jumps, 3 table tops, misc. bumps,...
Replies: 3,214
Views: 432,311
Posted By MHall

RE: The Official Traxxas Slash short-course race truck

Can sombody tell me what the reason for the sleeve on the motor is for? Was told by some it is a heat sink and other say it improves performance... I race the truck and the sleeve is heavy dead...
10-19-2008, 08:51 PM
Replies: 4
Views: 686
Posted By MHall

RE: measuring pitch angle !

Thank You for the help/ info. ;)
10-19-2008, 12:40 PM
Replies: 4
Views: 686
Posted By MHall

RE: measuring pitch angle !

I read the prior explination but need more help. I crashed my B400 and rebuilt it but was advised to recheck the pitch on the paddles and mains, so I picked up the E-Flite pitch guage and have no...
10-13-2008, 11:50 PM
Replies: 12
Views: 1,441
Posted By MHall

RE: JR servos for B400

I just picked up my first Heli yesterday, the B400!! My friends at the LHS recommended that I replace the tail servo with a digital. I picked up a JR DS290G, according to JR's web site it is their...
Forum: RC Jets
10-22-2005, 11:27 PM
Replies: 62
Views: 8,012
Posted By MHall

RE: F-18F Super Hornet (What Do You Think?)

The one you have linked to is the new Skymaster Diamond Backs Super Hornet. I have seen that very jet and is the most beautiful one that I have seen to date. It has full panel lines and rivets. The...
Forum: RC Jets
09-05-2005, 10:28 PM
Replies: 52
Views: 4,967
Posted By MHall

RE: New toy

Just a shot of it for you. ;)
Forum: RC Jets
09-05-2005, 10:22 PM
Replies: 52
Views: 4,967
Posted By MHall

RE: New toy

Hay Carlos,
How is my Roo doing??? I figured it would be easier for you to pick it up at Marks so I took it there Sat. for you. I found a new place to live today so the timing could not be better...
Forum: RC Jets
08-24-2005, 11:41 PM
Replies: 30
Views: 3,717
Posted By MHall

RE: All Turbine Pilots should have this, it is important

I agree, but at least it shows that we are PRO-active not just Re-active. [8D]
Forum: RC Jets
08-24-2005, 11:17 PM
Replies: 7
Views: 1,359
Posted By MHall

Showing results 1 to 25 of 433
 


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.