Excess to my needs, cutting back on flyable R/C planes due to illness
Willing to Trade:
FUTABA 14SGA system consists of: 1 14SGA Computer System Transmitter w charger and 1 extra tx battery (Futaba HT5F1800B NiMH Transmitter Battery 4PX/14SG ) 2 Futaba R617FS recievers,1 R7018SB reciever 1 Powerbox GEMINI II battery backer system all in original packaging with manuals etc.
see FUTABA kink here >>> https://youtu.be/qPIdWHuWL1w
NOTE 1: the tx currently has 5 programs in it, I can leave these in or delete them buyers choice NoTE 2: The Gemini unit adds reliability by taking power from 2 batteries evenly and distributing it to the reciever, all of my planes use some form of powerbox systems for added battery reliability.
All Specifications follow:
This is the Futaba 14SGA 14 Channel 2.4GHz Computer Radio System on Mode 2
**Does Not Include Servos** This is the Mode 2 version-the left stick controls throttle and rudder and the right stick controls elevator and ailerons This is the airplane version which will default to airplane settings when powered up.
FEATURES 2.4GHz FASSTest technology is also compatible with Futaba FASST and S-FHSS protocols, allowing this system to be used with most 2.4GHz air receiver Futaba produces Transmits and receives telemetry data with Futaba telemetry sensors (not included, sold separately) to monitor flight data, receive alerts and more, see COMMENTS below 30 model memory with 10 character model naming and 10 character user naming Model data can be saved to an SD card (not included, purchase separately SD:32MG-2GB, SDHC:4GB-32GB) One year limited warranty through Hobby Services beginning at date of purchase Left and right assignable slider switches Two assignable rotary knobs Six assignable three-position switches One assignable momentary two-position switch One assignable two-position switch S.BUS2 programmability allows multiple servos, gyros and telemetry to be installed with minimum amount of cables Programming port and earphone jack Airplane Features; 7 different wing types, 3 different tail types, 2 different rudder types Flap setting menu Differential ailerons Aileron to camber flap mixing, aileron to rudder mixing Rudder to aileron mixing and rudder to elevator mixing Camber mixing, elevator to camber mixing, camber flap to elevator mixing Snap roll, V-tail and airbrake mixing Ailevator Winglet Motor mixing Fuel mixture mixing (single and twin) Gyro mixing Throttle curve (5-point), Pitch curve (5-point) Idle down Helicopter Features; 6 swash plate types Pitch/throttle curves (5-point) Throttle hold Swash mix Throttle mix Pitch to rudder mixing Fuel mixture Gyro (flybarless support) Governor (700-3500 rpm) Hover pitch and throttle High/low pitch Swash AFR Swash setting (mixing rate, linkage and speed compensation), swash ring (electronic) Throttle cut Glider Features: 11 different wing types, 3 different tail types, 2 different rudder types Flap setting menu Differential Ailerons Aileron to camber flap mixing Aileron to brake flap mixing Aileron to rudder and rudder to aileron mixing Rudder to elevator mixing Camber mixing Elevator to camber mixing Camber flap to elevator mixing Butterfly mixing, butterfly to elevator mixing
INCLUDES Futaba 14SG 14 Channel 2.4GHz Computer Radio System on Mode 2 , 6V 1800mAh NiMH Transmitter Battery, Instruction Manual, and LiFe Spacer for optional FT2F2100B/FT2F1700B battery* pack, Battery Charger, and Switch Harness
REQUIREMENTS Servos of modeler's choice
SPECIFICATIONS Transmitter; Transmitting Frequency: 2.4GHz band System: FASSTest14CH, FASSTest12CH, FASST MULTI, FASST 7CH, S-FHSS switchable Power Supply: 6.0V HT5F1800B NiMH battery (FUTM1482) Receiving Frequency: 2.4GHz FASSTest system Power Requirement: 3.7 - 7.4V (voltage range 3.5 - 8.4V) Current drain: 75mA Extra Voltage Port: 0 - 70V DC Size: 0.98 x 1.9 x 0.56 (24.9 x 47.3 x 14.3mm) Weight: 34.5oz (980g)
This is the Futaba R617FS 2.4GHz FASST 7-Channel Park Flyer to Giant Scale Aircraft Receiver.
FEATURES High sensitivity receiver weighs only .25oz (7g) without case yet is a full range system for all aircraft from giant scale to park flyer applications-no need to buy separate receiver for specific aircraft Simple one-touch linking - no plugs to mess with or lose Dual Antenna Diversity allows 2.4GHz FASST Futaba transmitter to select the best reception between the two receiver antennas with no signal loss Rubber grommets installed where antennas exit to eliminate stress and fraying of the two antenna wires One year limited warranty
INCLUDES Futaba R617FS 2.4GHz FASST 7-Channel Receiver
SPECIFICATIONS Size: 1.6 x 1.1 x .35 (40 x 27 x 9mm) Power Requirement: 4.8 - 6V Current Drain: 80mA (at no signal), 74 mA(w/ signal no servos on 4.8) Weight: 0.34oz (9.8g) with case, 0.25oz (7g) without case Antenna Length:5-1/2
Gemini II specs
Product description: The Gemini II is the logical development of the PowerBox Gemini, which we have produced unchanged since 2005. The revised design incorporates ideas gleaned from customer requests and our own experience. The Gemini II has a considerably higher performance than the earlier model, since the case now consists of a high-quality machined aluminium heat-sink. Numerous supplementary features have also been added. For example, the pilot now has two options for activating the system: either by push-button using the SensorSwitch, or using a magnet. This also allows the implementation of a concealed installation; in this case an integral buzzer indicates the ON and OFF state.
Like all power supply systems from PowerBox Systems, the Gemini II boasts consistent redundant construction: two regulators, two controllers and two integral Hall sensors ensure a totally reliable power supply. The external SensorSwitch activates both electronic switches simultaneously. The tri-colour LEDs in the SensorSwitch indicate the battery status in four stages. The battery inputs take the form of MPX high-current connectors. The output voltage is double-regulated, and can be set either to 5.9 V or 7.4 V. Features: Double-regulated output voltages for receivers and servos Electronic On / Off switch, using either a magnetic trigger or the SensorSwitch On and Off switching signalled by visual and audible indicators Regulated output voltage of 5.9 V or 7.4 V LED voltage indicator for each battery separately Supports three battery types: LiPo, NiMH / NiCd, LiFePo Suppression of any servo feedback currents which might occur MPX battery inputs Technical Data: Operating voltage 4.0V - 9.0V Power supply 2S LiPo, 2S LiFePo, 5S NiCd/NiMH Current drain Power-on state 56mA Current drain Standby 16µA Maximum load current Peak 2x6A Drop-out voltage 0.3V Output voltage 5.9V or 7.4V regulated Dimensions 60x30x15 mm