Razzle 3d?
 

is the razzle 3d a good plane for 3d flying? will it do Harrier, rolling harrier, blender, hovering, and all that good stuff?

Kyle

RE: Razzle 3d?
 

yup:D

RE: Razzle 3d?
 

If you can stomach the colors then it should be alright. IMO a UCD would be a better choice.

RE: Razzle 3d?
 

I don't like it... No counterbalaances on the elevators and a miniscule one on the rudder.

RE: Razzle 3d?
 

i just picked up a few planes for areally good deal and i may be keeping the razzle so i was just wondering how it would fly. i am flying a H9 funtana right now. i can handle the colors. maby i'll test fly it this weekend.

Kyle

RE: Razzle 3d?
 

I LOVE MINE YS 110 ALL JR 8231 BUT THE THORDUL HS 55 FLY A LOT LIKE MY 3D AND I LOVE THE COLOR:D

RE: Razzle 3d?
 

YS 110. hmm. mine came with a ASP .61 2 stroke. i know the 61 is at the bottom of the engine range but do you thing this will have the umph to 3d it? if it doesnt i can always find a way to get a bigger engine. maby a YS 110. i have the YS 63 and the YS 120, i think i need the 110 dont you?:D

Kyle

RE: Razzle 3d?
 

yea it has idlel and flying and warp speed pullout i thing it mite be faster than my funtana with satio 100 i know its faster than my u cant do 3d with the satio 150 on it but it a really good mach for the plane and yes yes yes you need ys 110 i have herd a lot of bad about the ys but maybe they dont know what there talking about i have 4 of them now and so far they run great

RE: Razzle 3d?
 

Bull****e...
The Razzle will hover at half with any decent BB 60.
Period.
Mine with a 91 will also, buy you better not go full throttle unless your vertical.

RE: Razzle 3d?
 

hay from above i did not say it would not but i dont think it will after all the hangar 9 cap is smaller in all ways it wont hover and half trodle with a 60 ummmmmmmmm satio 100 half 60 half ummmmmmmmmm my ys hangs at 1/4 power with 3/4 thordle to pull out da hover i just dont see that size plane hanging with a 60 at half power QUOTE as for bull****e or is it ummmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmmm:(

RE: Razzle 3d?
 

I hate to sound superior here but.....

Posts like the last one really give me an appreciation of a subject I literally slept through in high school......English!

Never thought I would say this in my entire life but punctuation DOES have it's merits!

RE: Razzle 3d?
 

ok, back to the razzle. so the 61 should be able to hover it? i dont care if it is at half throttle or 3/4 throttle really. as long as it will come out of a hover without dropping the nose.

I love both my YS engines and YS is the only 4 stroke engine i will use, maby a saito, but i like to stick with YS. the fact that the YS was my 1st 4 stroke adds a bit to my obsession with them.:eek:

Kyle

RE: Razzle 3d?
 

Kyle, put a good prop on the 60 and give it a shot. You can always get another engine later if you aren't happy with it.

RE: Razzle 3d?
 

I flew my Razzle with a supertiger x-61 and it did okay. It took all it had with a 14-4 to hover it, would not pull out very well. When I recover the wing, I will put a 4-stroke 90 or something close to it to help with the power department.
Good luck with your 61, it just might do better than mine.
v-snap

RE: Razzle 3d?
 

will do Ryan. i also have a H9 cap 232 40 that has a THunder tiger pro 46 on it that i need to test fly. whatever one flies the best i will keep.:D

Kyle

RE: Razzle 3d?
 

Post removed by moderator

RE: Razzle 3d?
 

HEY!

chill

RE: Razzle 3d?
 

I would personally go with a APC 13X4 W on the 60/61 two stroke. You'll get it to hover fine. This plane assembles so light for a 60 size bird, it's unreal.
The 4 strokes handle the bigger props better.
Yes, I own one and have over 100 flights on mine.

RE: Razzle 3d?
 

APC 13x4 W huh. i'll try that. how do you thing a master airscrew 13x6 would work?? or anywhere in the 13 inch props.

Kyle

RE: Razzle 3d?
 

I just bought this plane yesterday. The weight quoted on the box says 5.9 to 6.4 lbs. This thing seems awful big to weigh so little - anyone have weights to report? My fuse alone feels heavy. Please pass on your engine choice too. I'm thinking Saito 100 for mine.

The plane looks great. I don't think the red and purple match too well, but other than that this plane is a thing of beauty. Those Vietnamese children do good work.:D

Kurt

RE: Razzle 3d?
 

p-p-pun..ctu..ation?? ;)

RE: Razzle 3d?
 

13X4 W only for a funfly...all the funfly props work fine..only on this combo, Razzel/61 a 13X4 W
Not a 13X6, it won't rev up quick enough to hover well.

RE: Razzle 3d?
 

Mine came in at 7 lbs with an OS91FX. A little disapointing. Flys great with either a 14/6apc or a 15/4 apc. Hovers great and does missle shots out of a hover;). At 7lbs I think it's a bit much for a 60 to do missile shots or knife edge loops but it would still be a great flyer.

Denis

RE: Razzle 3d?
 

ok so 13x4 W is good, 13x6 is bad. gocha:)

RE: Razzle 3d?
 

kyle my name is jerry kitchin i have a razzle with a o.s. 91 surpass it is the best 3d model i have even flown thanks it weighs 5.5lbs it will hover at half throttle