RE: Capiche 90 3D!!!
 

Not possible Edible.

YS 110 is 10oz heavier.

Add extra weights of tank,prop and motor mount you will be lucky to get sub 8 lbs

RE: Capiche 90 3D!!!
 

8 lbs would still be an excellent weight for that many 'orses !

RE: Capiche 90 3D!!!
 

OK... so where do I send the funds!;)

RE: Capiche 90 3D!!!
 

i new i wasnt possible malc :eek: but 8lbs with a YS110 would be awesome!

RE: Capiche 90 3D!!!
 

I think that would only come near to 8 lb if it was all composite, but then the price would be just silly.

I know a YS 63 is miles ahead of an Irvine .53 but if I had to, how would the C90 do with one?

RE: Capiche 90 3D!!!
 

just cos its composite doesnt mean its light weight! if its craply made its gonan be heavy, well made with top materials itll be light as a feather. however, blasa is also light weight;)

RE: Capiche 90 3D!!!
 

Of course I meant the top-quality you wally! Personally I prefer balsa, only though because its is repairable and availble cheaply. Compared to 1/2 square metre carbon fibre for £20![X(]

RE: Capiche 90 3D!!!
 

if only ;)

RE: Capiche 90 3D!!!
 

That was not exactly very nice Philly was it? ;)

RE: Capiche 90 3D!!!
 

sub 8Lbs with the 110 is perfectly doable

mine is 7lb 10, with the os90fx, the ys110 is almost the same weight.

when I get the chance the 110 is going in mine to replace malcs os90fx,

RE: Capiche 90 3D!!!
 

There yo have it folks! :D:D:D

RE: Capiche 90 3D!!!
 

Oh yes - this plane will dance with a 110 - do you realise how much power those babies have !
[X(]

RE: Capiche 90 3D!!!
 

must.....get....one
cmon archie u no u want to
how do they perform wiv a 91fx? my budget is pretty small but i must have one of those!!!!

RE: Capiche 90 3D!!!
 

Hi guys I'm back. Been on holiday to California :D

Looking good Malc. Though it looks like the 140 in size! Must be the angle for the photo.

Yep, definately need one of these in my life :D

RE: Capiche 90 3D!!!
 

Sprink - check out the 140 thread for the latest 140 awaiting test..

RE: Capiche 90 3D!!!
 

in the flesh the 90 is a fair bit smaller than the 140, however as 90 size models go its actually quite big.

RE: Capiche 90 3D!!!
 

So it looks like it might actually be happening:D, even if it is a limited production run.

I know that I'll be ordering one. YS 110 to power it I think :D

RE: Capiche 90 3D!!!
 

I put in my interest in the website, I hopes they arnt toooo much money, seems nice though, not too big so it wont burn a wallt and not too small either, my C50 got a fair bit of attention, wonder how this will fair :D

RE: Capiche 90 3D!!!
 

I'm fairly certain it wont be less than £200. Remember that it is a C140, but a bit smaller, little scope for savings really.

Still want one though :D

RE: Capiche 90 3D!!!
 

Your probably right, even if the kit is slightly less expensive the engine, stuff etc will be much lesss I hope so you end up with a cheaper airplane to initally buy and mebbe run to.

RE: Capiche 90 3D!!!
 

Certainly fitting out would be a lot cheaper:

OS 91 FX at £150 - or cheaper if going used or a cheaper make
4 Good servos at £30 each = £120

Depending on the price of the kit, you could get a decent performance for £500 - £600. For the C140, you are really looking at £1000+, though if really scrimping, I think you could get it down to £800, but then you are likely to start affecting performance.

RE: Capiche 90 3D!!!
 

[8D]

RE: Capiche 90 3D!!!
 

Servo wise 3010's? Or is that like putting 3004's in the.

9202's always looked juicy but they a bomb, even if I get them discounted.

I got £60! But thats going straight to my dad since its his £60 [&:]

RE: Capiche 90 3D!!!
 

Any news on this plane???

RE: Capiche 90 3D!!!
 

yeh, i crashed the prototype at the freestyle meet on saturday night [:o] i twas flying the bollocks then..... it was a foot in the ground [:@]

i think it should be kitted (or even better get the ARF treatment!!:D)

Dave