New product for multiple airplane owners
1 Attachment(s)
<div style="margin: 0in 0in 0pt">Use one receiver for multiple airplanes with this gadget. I probably have $500.00 worth of Futaba R617FS receivers alone and I am sure some of you have much more. If you could easily move you receiver from plane to plane to save $80 per plane would you?</div><div style="margin: 0in 0in 0pt"> </div><div style="margin: 0in 0in 0pt">There is a company I have used to make something similar to this if I have a bunch made at once its much cheaper. I am thinking about having a lot of them made, even for different radio systems. I am looking for replies on weather people think they would purchase and or use something like this before I go out and make a whole bunch of them. I think they will cost 9-15 dollars not sure yet.</div><div style="margin: 0in 0in 0pt"> </div><div style="margin: 0in 0in 0pt">As shown in illustration, the circuit board shock mounts to the plane with all the servo leads hooked to it. Just plug the receiver in face down on the connector and slip the antennas it to the tubes. Don’t forget to change models on your transmitter.</div><div style="margin: 0in 0in 0pt"> </div><div style="margin: 0in 0in 0pt">If I make one for the Spectrum I will have to figure out a way around the model match feature.</div>
|
RE: New product for multiple airplane owners
Not a bad idea.....Rog
|
RE: New product for multiple airplane owners
yeah that is pretty neat...i like that the receiver plugs in...there are similar items like this that cost hundred of dollars and have too many bells and whistles....i wouldnt mind something like this for planes i dont fly on a regular basis
|
RE: New product for multiple airplane owners
! Good Idea! Have you actually tried and tested this interface and configuration?
Yes, I might be interested. |
RE: New product for multiple airplane owners
That is awesome! I would buy some of those. radio manufacturers would never sell something like that because they want to sell you a receiver for every model. I think you have yourself a good product there.
|
RE: New product for multiple airplane owners
Just today I started looking for a new futaba 9ch PCM. I only have one and it's in use but I sure could use another one right now!! That would cure my problem.
|
RE: New product for multiple airplane owners
Quite brilliant!
|
RE: New product for multiple airplane owners
Oooh, I like!
|
RE: New product for multiple airplane owners
I like!!!! Great idea!
|
RE: New product for multiple airplane owners
I have to admit I was skeptical when I started reading your post, but when I saw your illustration, I really liked it. I would recommend adding a velcro strap around the antenna end of the adapter to keep mechanical loads off the connectors.
The key will be finding a good price point where you can make a profit, yet sell cheaply enough to encourage people to own several. |
RE: New product for multiple airplane owners
i would be interested in a few of them
|
RE: New product for multiple airplane owners
what i do is plug everything into rx, then jam notecards/paper into the gaps between the plugs and glue/ziptie the plugs/paper together. that way i can just plug or unplug one thing.
thats not a bad idea at all though, just dont skimp out on the plugs/wire so we can use highcurrent servo's. dont use those thin silver/solder strips, they melt under high current way to easily |
RE: New product for multiple airplane owners
Looks similar to Smart Fly, imo Bob |
RE: New product for multiple airplane owners
I just looked a one of my R617FS receivers and found that the antenna wires come out of the "bottom" end of the receiver; opposite end of the servo connections. The location of the tubes would need to be changed or just left off of the tray.
STILL a good idea! |
RE: New product for multiple airplane owners
Very nice, I have Hitec 2.4 would like several.
Jon |
RE: New product for multiple airplane owners
To echo a quote often heard in our house full of teenagers....."Waaaaay Cool!!!"
I like it. Especially as referenced above, for seldom flown a/c. "If I make one for the Spectrum I will have to figure out a way around the model match feature" Why increase cost and muddy-up the simplicity?Even for Spektrum 2.4, how long does it take to bind a receiver? 30 seconds? Easy enough for me to be very intrested in a few. If someone is too slack to want to have to rebind after swapping a/c, they're not going to be intrested in swapping the receiver out in the first pace would be my guess. |
RE: New product for multiple airplane owners
Nice!
Interested if you can figure out the "Spektrum" issue. |
RE: New product for multiple airplane owners
Nice Idea,
Just a thought, If you add one more plug on the servo end, you could use all 7 channels without Y-cord. |
RE: New product for multiple airplane owners
Sounds great I'd like to have a few. http://www.rcuniverse.com/forum/js/f...sn/thumbup.gif
|
RE: New product for multiple airplane owners
Wait...why don't you just set up the recievers in your plane to be easily removed without the need for a board like that? I have multiple planes that all fly on the same reciever because i take it out and move it. Thats all..
|
RE: New product for multiple airplane owners
ORIGINAL: brickhead179 Wait...why don't you just set up the recievers in your plane to be easily removed without the need for a board like that? I have multiple planes that all fly on the same reciever because i take it out and move it. Thats all.. |
RE: New product for multiple airplane owners
1 Attachment(s)
I've used this type of multi-pin connector to shuffle receivers around. You need one with more pins, but this is the general idea. Use one end on your receiver platform and the other end you connect to all your servos. The side that connects to the servos stays in the plane, so you need one for each plane you have. Then you just need to plug that one connector to the connector on your servo platform and you're ready to go. If you could make a production run that was a reasonable cost I'd like some. A pain to make, lots of little soldering.
|
RE: New product for multiple airplane owners
ORIGINAL: Gray Beard ORIGINAL: brickhead179 Wait...why don't you just set up the recievers in your plane to be easily removed without the need for a board like that? I have multiple planes that all fly on the same reciever because i take it out and move it. Thats all.. |
RE: New product for multiple airplane owners
When will I ever learn to stop quoting myself instead of editing?
|
RE: New product for multiple airplane owners
Great idea! I currently have 10 R617FS receivers, all currently in planes. I could have saved a bundle with something like that.:D
Bruce |
RE: New product for multiple airplane owners
I Will Take 5 To start with with the possability of more for Perchase. Please Let me Know when you get started on selling these. I have a Futaba 10c and this would help out alot
|
RE: New product for multiple airplane owners
Ring me up!!!!! That idea's great.
|
RE: New product for multiple airplane owners
very cool. i'd love something like this for surface models, even if the receivers are cheap by comparison.
|
RE: New product for multiple airplane owners
I definitely like this idea. I love my Futaba 7C 2.4 but I hate how much the receivers cost. I have 6 planes and only three of them are on 2.4. I'll take three!
|
RE: New product for multiple airplane owners
Sorry, I must be missing something? Dont I have to move the same amount of plugs? what does this save?
I move my RX from plane to plane now... Steve |
RE: New product for multiple airplane owners
ORIGINAL: Popriv Sorry, I must be missing something? Dont I have to move the same amount of plugs? what does this save? I move my RX from plane to plane now... Steve Get the Rx plug port to go horizontal with the board for my Spectrum Rx's and I will re-bind when I make a switch. My radio will keep the model memory anyway and that's the hard part (setting up the plane in the Tx). Ahh forget it... I'll build a prototype tonight and beat ya to the market:D |
RE: New product for multiple airplane owners
Pretty cool, I have Hitec 2.4 and I'm interested.
|
RE: New product for multiple airplane owners
1 Attachment(s)
ORIGINAL: Popriv Sorry, I must be missing something? Dont I have to move the same amount of plugs? what does this save? I move my RX from plane to plane now... Steve |
RE: New product for multiple airplane owners
Do you have an idea how much would cost?
|
RE: New product for multiple airplane owners
ORIGINAL: devinatoraviator Do you have an idea how much would cost? |
RE: New product for multiple airplane owners
I like the idea very much. At present I have 14 planes so this would save me A BUNCH of money (not to mention it will PO the wife since I can add more planes :D )
When do you think you might have a price and will they be available for other receivers also? |
RE: New product for multiple airplane owners
This is a very ingenius idea! I'd probably be up for a few if the price is right!
|
RE: New product for multiple airplane owners
Great idea, but if you are talking about a circuit board with traces, you are going to have to turn the servo plugs 90 deg. so they can be soldered to the board. If you used a two sided board you could have the signal traces on one side and the power and ground on the other side in the form of a bus. Or do you plan on using three wire from tx plug to rx plug; that would be really easy for a diy type person.
Oscar |
RE: New product for multiple airplane owners
Two thumbs up for one heck of a GREAT idea!
|
RE: New product for multiple airplane owners
I agree, great idea, just one question, will it be a "one size fits all" or will there be different boards depending on number of channels?
|
All times are GMT -8. The time now is 11:54 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.