E3D Power System
04-19-2003 | 03:34 AM
#1
Thread Starter
Junior Member
Joined: Apr 2003
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
From: Estes Park, CO
E3D Power System
I'm looking for advice on power systems for Gary Wright E3D !
Gary recommends the Hacker C-40 w/6.0:1 gear drive!
MEC recommends the brushless 22/20/2 Mega motor with
Super Box 4.0:1 gear drive!
If anyone knows more than this, please advise me!
Don Jeune
[email protected]
Gary recommends the Hacker C-40 w/6.0:1 gear drive!
MEC recommends the brushless 22/20/2 Mega motor with
Super Box 4.0:1 gear drive!
If anyone knows more than this, please advise me!
Don Jeune
[email protected]
04-19-2003 | 09:29 AM
#2
Joined: Jan 2002
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts
From: Champaign Il
E3D Power System
sanyo HR-SC 2600mah nimh 10-cell for all of the below (zapped of course). Below prices are motor/esc combo costs with average street prices
budget setup with good prformance, about $75
Endo, 4.6, 12X8 prop
More expensive, far better performance $190
Mega 22/20/2 4.0 ratio with 14X7 , hacker 40-3P master controller
"ferrari" setup, about $270
Hacker C40 12T, 5.0, 14X7,hacker 40-3P master controller
Various components and cost
Endo, $25
C50 ESC, $50
Mega 22/20/2 $90
hacker master 40-3P controller $100
Hacker C40 12T motor $170
budget setup with good prformance, about $75
Endo, 4.6, 12X8 prop
More expensive, far better performance $190
Mega 22/20/2 4.0 ratio with 14X7 , hacker 40-3P master controller
"ferrari" setup, about $270
Hacker C40 12T, 5.0, 14X7,hacker 40-3P master controller
Various components and cost
Endo, $25
C50 ESC, $50
Mega 22/20/2 $90
hacker master 40-3P controller $100
Hacker C40 12T motor $170
04-20-2003 | 12:15 AM
#3
Thread Starter
Junior Member
Joined: Apr 2003
Posts: 8
Likes: 0
Received 0 Likes
on
0 Posts
From: Estes Park, CO
E3D Power System
Sorry Gary, I responded before reading the second response
you presented!!!
Your explanation in the second response was what I needed!
Thanks for doing that!!
Don Jeune
[email protected]
you presented!!!
Your explanation in the second response was what I needed!
Thanks for doing that!!
Don Jeune
[email protected]
04-20-2003 | 03:53 AM
#4
Senior Member
Joined: Nov 2002
Posts: 162
Likes: 0
Received 0 Likes
on
0 Posts
From: Fremont, CA.
E3D Power System
Hello Friend,
I don't have an E3D, but build 4 of them. Do you have a back round in E-planes? Gwright's recomendations is included in this reading materials
I don't have an E3D, but build 4 of them. Do you have a back round in E-planes? Gwright's recomendations is included in this reading materials
04-21-2003 | 11:40 AM
#5
Joined: Jan 2002
Posts: 390
Likes: 0
Received 0 Likes
on
0 Posts
From: Champaign Il
E3D Power System
cody,.. responded to your new emails yesterday, got more error messages from postmaster. Since I get mail from a multitude of sources and reply without problems,..it's probably something with netzero.
