Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
<span lang="en" id="result_box"><span class="hps">Hello,</span>
<span class="hps">Here are pictures of</span> <span class="hps">mounting</span> <span class="hps">Hacker</span> <span class="hps atn">Q80-</span><span>14XS</span> <span class="hps">F3A</span> <span class="hps">in the</span> <span class="hps">PHOENIX</span><span>-E</span> <span class="hps">CBmodelisme </span>http://img4.hostingpics.net/thumbs/m...q8014xsf3a.jpg http://img4.hostingpics.net/thumbs/m...8014xsf3a1.jpg http://img4.hostingpics.net/thumbs/m...kerq8014xs.jpg <span class="hps">Benoit</span> <span class="hps">Chauvet</span> <span class="hps">CBmodélisme</span> <span class="hps">www.cbmodelisme.com</span></span> |
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
Hello Benoit,
Have you weighed this new light weight motor yet? Regards, Jason. |
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
<span lang="en" class="short_text" id="result_box"><span class="hps">Hello</span> <span class="hps">Jason,</span>
<span class="hps">The new engine</span> <span class="hps">weighs</span> <span class="hps">574g Benoît Chauvet CBmodélisme www.cbmodelisme.com </span></span> |
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
Hello,
The first Phoenix-E with Q80 his ready to fly. <span lang="en" class="short_text" id="result_box"><span class="hps">The weight is</span> <span class="hps">4850g</span> <span class="hps">with a</span> <span class="hps">5000mAh</span> <span class="hps">lipo</span> <span class="hps">10S ! www.cbmodelisme.com </span></span> |
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
1 Attachment(s)
|
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
1 Attachment(s)
|
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
If I may ask, is the material G10 (circuit board) ? Any plans to also rear support ?
|
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
1 Attachment(s)
<span lang="en" id="result_box"><span class="hps">In the photo</span> <span class="hps">are not present</span> <span class="hps">the</span> <span class="hps">interuptor</span> <span class="hps">receiver</span> <span class="hps">and</span> <span class="hps">receiver batteries (lipo 2S 1000mAh)</span> <span class="hps">and</span> <span class="hps">controller</span> <span class="hps">voltage</span> <span class="hps">but they are</span> <span class="hps">included in the weight</span> <span class="hps atn">(</span><span>4850g</span><span>)</span></span>
|
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
1 Attachment(s)
|
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
Benoit, your Phoenix-E is absolutely beautiful. I really like the "clean" installation of you elevators and rudder___Nice, very nice. Everette
|
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
Finally someones thinking about where to install a rudder servo !!
Fantastic job ! |
RE: Hacker Q80-14XS F3A in the PHOENIX-E CBmodelisme
Flyer88, you need to check out the 2M Monolog at F3A Unlimited. It has a "rear'" mounted servo rudder along with all the rest of the line of BJ Craft's 2M pattern planes. You will pay a little more but, you will get sooooo much more! Regards, Everette
|
All times are GMT -8. The time now is 08:27 AM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.