RCU Forums

RCU Forums (https://www.rcuniverse.com/forum/)
-   Engine Conversions (https://www.rcuniverse.com/forum/engine-conversions-92/)
-   -   super tiger 18 engine (https://www.rcuniverse.com/forum/engine-conversions-92/11618365-super-tiger-18-engine.html)

djalex_4ever 06-13-2015 11:29 AM

super tiger 18 engine
 
Hi everybody,Iīm Alex and I have a lamborghini rc under build right now and I have a big problem with the engine.Seems like the piston dosenīt have enough room in the cylinder liner to complet a cicle and gets stuck i will put a video here is more easy to see what iīm talking about https://www.youtube.com/watch?v=VnvW7-Wjuzs When the connecting rod is down the cylinder liner is completely in on the chamber but when the coonnectin rod push up the piston the cylinder liner is getting out and thats wrong i think....so what can i do in this situation???

captinjohn 06-13-2015 05:10 PM

Warm up the cyl /sleeve with a low flame using a propane torch. Then see if engine frees up. Do not heat the piston...just the upper sleeve.

djalex_4ever 06-13-2015 10:46 PM

ok, I will try that,thanks

KenLambert 06-13-2015 11:36 PM

is it a new engine? if so put it back together and break it in .the abc engines are tight in that area.

djalex_4ever 06-14-2015 12:12 AM

brand new...and iīve put it all together and that was the moment when iīve seen that the piston dosenīt have enough room to complet the cicle.so your telling me to do the same and just force the piston and the cylinder liner ??

KenLambert 06-14-2015 12:44 AM

the cylinder head should hold the liner in place. use a small amount of oil, I use 3n1 oil and work the crank back and forth and it should eventually turn over with minimal force. or send it to tower and they will fix you up. also leave the plug out.

djalex_4ever 06-14-2015 12:53 AM

ok,I will try with oil....hope to solve this :D thanks

bluejets 06-14-2015 02:15 AM

It's normal.
Add some fuel/oil mix as suggested above.
K&B 40 marine will actually squeak going over the top even with fuel.
Try to avoid pulling the engine apart in future as the manufacturer may well get a little upset and void any warranty.

djalex_4ever 06-14-2015 02:27 AM

i didnīt pull the engine apart,it came that way,and i have to build it from parts....the oil solution i think its working....thanks to all :)

coriolan 06-14-2015 08:58 AM

This is normal for an ABC engine as the sleeve is tapered toward the top, as the engine runs and warm-up the fit will be perfect.
https://youtu.be/VnvW7-Wjuzs
If it wasn't doing that it would mean the P/S fit is too loose!

bluejets 06-14-2015 02:57 PM


Originally Posted by djalex_4ever (Post 12054745)
i didnīt pull the engine apart,it came that way,and i have to build it from parts

Anyone else ever seen a Super Tigre engine delivered this way, as it is a first for me.

captinjohn 06-15-2015 12:45 PM

I have not!!!!!!!!

1QwkSport2.5r 06-15-2015 03:31 PM


Originally Posted by captinjohn (Post 12055562)
I have not!!!!!!!!

Me neither.

KenLambert 06-15-2015 08:07 PM

depends on where you got it from


All times are GMT -8. The time now is 01:23 PM.


Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.