Conversion Photos
 

Seems this topic (Conversion Engines) needs a thread full of good conversion photos all in one handy thread. So how about posting your favorite photos of your conversion engine either mounted in your plane, setting on the bench, or heck.......you can just post a photo of your favorite weed whacker.lol

Here are a few photos of mine I wanted to share. The Rascal 110 has a Ryobi 31cc mounted in the nose. It is stock single ring with a stock Zama carb swinging an 18x6 prop around 7200rpm. Flys the plane scale-like and runs smooth as butter. The conversion parts were made by a fellow friend and flyer (RCU member XTOL).

The photo of the all blue engine is a 28.5cc Ryobi short shaft single ring with a Walbro carb. This engine is going into a giant profile plane, and then into a Super Sportster 90/120 size I am going to finish building this winter.

LETS SEE YOURS!!!!

RE: Conversion Photos
 

I love your engine paint job. What did you use for paint ? As soon as I get
some good pictures, I will post mine. Good idea ! a picture is worth .

RE: Conversion Photos
 

I use rust-oleum impliment paint. I just "deglaze" the engine using Dawn power desolver. It helps to create a surface that the paint really adheres to well and the paint also seems to hold up to the heat very good. As far as I can tell it has little or no negative effect on cooling. I have checked the head temps several time, and it runs cool as a cucumber and actually I have no proof, but I think it may also help to dampen the engines harmonics and give it a more mellow sound. The stock Ryobi finish is not exactly "purty". Ford Blue is kinda my color, and kinda makes my engines reflect my taste and personalizes it. I will look forward to your photos.

RE: Conversion Photos
 

The paint does better if you bake it in the oven around 275-300 F after it has dried for a week.

RE: Conversion Photos
 

Here is a test run of 2 ryobi's on my scratch built twin spad .

http://rcuvideos.com/video/engine-run-wmv

adrian

RE: Conversion Photos
 

Thanks for the tip w8ye, and thanks for sharing the vid adrian222. That spad twin looks like it would be a fun one!

RE: Conversion Photos
 

Here is a photo I forgot to include in my original post. This is the Ryobi 31 shown mounted in the Rascal 110 as I was rebuiulding sections of the plane where the original owner inflicted damage upon it. It worked out good for me when I recieved the plane because the firewall was destroyed. This allowed me to change the firewall location when I rebuilt it accomadate the heavier Ryobi. I ended up setting the firewall about 2 inches back from the stock location. This proved to work out fantastic because the plane balanced perfect when finished and the cowl has no unsightly cuts. Worked out very well and the Ryobi powers the plane good and scale like.

RE: Conversion Photos
 

Theres nothing like the sound of a twin. Gota love it.

RE: Conversion Photos
 

This is my 30cc Ryobi conversion to Marine engine, ported, walbro carb, 11800rpm without tune pipe.[img][/img][img][/img][img][/img]

RE: Conversion Photos
 

hmm, should have added in my conversions...

Poulan 21's:
http://i960.photobucket.com/albums/a...ril2010107.jpg
http://i960.photobucket.com/albums/a...ril2010108.jpg

Mac 32 on USL 120:
http://i960.photobucket.com/albums/a...raStick003.jpg
http://i960.photobucket.com/albums/a...raStick002.jpg

I have more on my computer, but it's still down from january when it crashed...

flew the USL on sunday, runs good just needed a bit of tuning and maybe a 18x6 prop instead of the 18x8

RE: Conversion Photos
 

heres a mc culloch md290 video http://www.youtube.com/watch?v=Ec5g0HUQcP8

RE: Conversion Photos
 

Below is a link to some video with a DLE30 running. You should see at least 4 other links to engines. The MB290 Mac engine run with ice on the engine was my most enteresting one. It has over 3 thousand views. Capt,n
<hr />http://www.youtube.com/watch?v=wl_3h-AjHYY
<hr />http://www.youtube.com/watch?v=c85M0...eature=channel

RE: Conversion Photos
 

[img][/img]

RE: Conversion Photos
 

Hello
ohh my fingers, but you can see a Weedeater poulan 25 cc and the Pioneer chainsaw conversion 40cc, actually with broken engine block, but can survive if we solder it.
We have in our club a McCulloch 40 cc engine flying, good engine good compresion,and a Niwa/Toyama chinese chainsaw, soft compression but good engine.
Thanks to RCuniverse in part these engines perform well and in part to RCU members.
Happy landings
Jose
Argentina

RE: Conversion Photos
 

The photo is an ECHO SB-1080. It is what BME uses for their 50. After doing about a dozen conversions I think this one is the best of the bunch. BME knew their stuff when they picked it. I fly it most weekends on a Bridi Big Bee. It runs great.

RE: Conversion Photos
 

that's a good running engine

RE: Conversion Photos
 

Click on my Gallery logo below and you can view some of my conversions and aircraft in work.

RE: Conversion Photos
 

Those Echo's look nice

RE: Conversion Photos
 

Here is one of mine a McCulloch 32CC and a Ryobi 31CC on two Charly Boys that I build and sell

RE: Conversion Photos
 

AERONUT Bill, I would really like to get in touch with you. Please check your Private Messages. I will leave my e-mail address there for you again.

Thanks and take care,
AV8TOR

RE: Conversion Photos
 

Here is my Honda GX35 working in a 2,4m Telemaster. Easy to start, runs great and the sound is beautiful.

For more information about this engine search here for GX35.

Some video and sound is here: http://media.rc-network.de/showgalle...500/ppuser/283

RE: Conversion Photos
 

Aeronut
How do I get info on the Charly Boy. I have several converted engines that need an airplane.

RE: Conversion Photos
 

Thomas,

Beautiful engine, plane and country side just East of Frankfurt

RE: Conversion Photos
 

w8ye

You know that area? The best is, that our flying field is just 3km from my home.
But not to break the content of this threat I stop here.
If you like to know more-> pn

RE: Conversion Photos
 

Twinstar, I build and sell these airplanes. give me a pm if you are interested.