I posted these on Runryder but thought they would help here too!

NEW - Just added Videos as of 4/14

[link=http://www.runryder.com/helicopter/t248187p1/]Installing and adjusting the pinion - Free Video[/link]

[link=http://www.runryder.com/helicopter/t248255p1/]Assembling the XL frames and bearings - Free Video[/link]

[link=http://www.runryder.com/helicopter/t250753p1/]Replacing the Autorotation Clutch - Free Video[/link]


Let me know what you all think!

[link=http://www.runryder.com/helicopter/t240822p1/]Servo Repair 101 - Free Video[/link]

[link=http://www.runryder.com/helicopter/p1846759/]Trex Canopy Trimming 101 - Free Video [/link]

[link=http://www.runryder.com/helicopter/p1846390/]Soldering ESC/Motor connectors 101 - Free Vid [/link]

[link=http://www.runryder.com/helicopter/t241026p1/]Soldering Deans Connectors 101[/link]

[link=http://www.runryder.com/helicopter/p1850494/]Ball Links 101 - FREE Video [/link]

[link=http://www.runryder.com/helicopter/t241462p1/]Installing Servos in an SE - FREE VIDEO [/link]

[link=http://www.runryder.com/helicopter/t241710p1/]CCPM Setup Part 1 - FREE VIDEO [/link]

[link=http://www.runryder.com/helicopter/t241944p1/]CCPM Setup Part 2 - FREE VIDEO[/link]

[link=http://www.runryder.com/helicopter/t242123p1]Thread Lock 101 - FREE VIDEO[/link]

[link=http://www.runryder.com/helicopter/t242170p1/]Setting up the Align ESC - FREE VIDEO[/link]

[link=http://www.runryder.com/helicopter/t242253p1/]Setting up the tail and GY401 Gyro - FREE VIDEO [/link]

[link=http://www.runryder.com/helicopter/t242568p1/]Pitch and Throttle Curves 101 - FREE VIDEO [/link]

[link=http://www.runryder.com/helicopter/t243398p1/]Setting up a Futaba 9Z basics[/link]

[link=http://www.runryder.com/helicopter/t246402p1/]Blade Balancing 101 - Free Video[/link]

[link=http://www.runryder.com/helicopter/t242748p1/]Electronics placement and trim adjustments[/link]




Bob

Pretty sweet man... thanks!!

These are awesome......are there any more where these came from?

Should do one on EXPO and build of t-rex Great work on them very informative [sm=thumbup.gif] better than the ones i have on build they are in chinese or something like that lol

Thanks for taking the time to make those...Great Job!

Thanks for this will be a BIG help.

Mr. Bob We all greatly appreciate the help... Those of us that do not have much experience in the model heli hobby will benefit most.
You've done a great job also...

Thanks again
Swazzi

I am new to helis and this has been so informative. Thank you very much for sharing and caring, people like you make the hobby what it is. fun fun fun
Al

OK just added a new video to my collection....

Setting up the 9Z for a new heli.

[link=http://www.runryder.com/helicopter/t243398p1/]Setting up a Futaba 9Z basics[/link]

Bob

Thank you! Thank you! Thank you!

awesome could you do one on how to use the eflite pitch guage

What do I think?

I think this is the best thread I've EVER read!

Thanks Bob, you've cured all the setup problems I had.

It's pure coincidence that I'd already bought the same radio gear and gyro you use in the videos so setup was a breeze.

I'm a total newbie but with your expertise, I can now hover with no problems at all

Tony

Bob,

Thanks very much for the videos. I've been flying RC helis for a bunch of years, and still learned a lot in most of the videos. Even on simple subjects, I learned a thing or two. Absolutely Great!

Bob,

Thank you for your wisdom and knowledge in the build and setup of the T-rex. It is people like you that make an excellent mentor for the rookies in the heli world. It is very gracious of you to take time out of your day (and produce videos) to help others understand the process required to construct a smooth flying bird. I thank you genuinely for your exceptional knowledge.

The Rookie

OK, Mark at RR did not like havinf direct links to the videos so i had to fix them all so they point ot the thread on RR with the link to the video.
Also I added 2 new videos!!!

Bob

would you mind if i put some of your links to your videos on our club website at www.flyingaeros.com
thanks

emilsanto ,

No NOT AT ALL! Just give me credit and your good to go........ I posted these for all to use and the more they are shared the better we all are for helping new people!

Bob

will do i will give you credit for the videos , i must say i was very confused about under standing pitch and throttle curves, i started flying heli's last year and all i could figure out was the normal mode. your videos really helped me under stand what i needed to do. now i need to set up my 30 size heli. the hobby is blessed to have someone who would take the time to make the videos. also if you decide to make anymore on seting up a nitro heli like a raptor ect.
pitch and throttle ect. please email me and i will post them on our web page. i am going to make a section just for you videos
thanks again
emil santo
warren ohio
www.flyingaeros.com

hello bob i posted links of you r videos on our website. looking in the videos section and our club fourm. at www.flyingaeros.com thanks again bob. if you would like to have any info put on our webpage just let me know. we need more people like you out there. i posted the videos in our forums. bob whites trex video forum.
thanks

Thanks! Looks good... Nice site you have for your club!

Bob

Bob,
Thanks a ton, these vids were perfect timing. I just bought and finished my Trex watching your vids. I would never have figured out the CCPM interacations without your help. Now how about some vids of how to fly
Rick

This stuff is the best it helped me way more than the setup page in the book that came with the bird
Thanks for the help Ray

VERY very good job and it`s FREE, not like others...
Now I`m downloading all of them and then I`ll fix my trex cause I have some problems.
THANKS

New videos just added to the list!

Enjoy,
Bob

[link=http://www.runryder.com/helicopter/t248187p1/]Installing and adjusting the pinion - Free Video[/link]

[link=http://www.runryder.com/helicopter/t248255p1/]Assembling the XL frames and bearings - Free Video[/link]

[link=http://www.runryder.comhelicopter/t250753p1/]Replacing the Autorotation Clutch - Free Video[/link]

hi,

the link for Replacing the Autorotation Clutch - Free Video
does not work - and i need exactly this one now ;-)))