RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

A Beatiful plane! I wish the manufacturer would go back into production on those Peashooters.

I've been wanting one since I ran accross that listing.


Unfortunately the lack of a sellable plane also points to a lack of parts too...

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

After an e-mail to Nitro they called me and are shipping 1 set of polyhedral wings.
Nice!!!

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

I still have not heard from them about a new canopy for my 71" FW 190 and a new 64mm fan for my F18

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Hi. I need a replacement cowl for the Edge 540T 46 - 52". My order # was yhst-17210252890263-139834. Here is a link to the ARF: http://www.nitroplanes.com/ed544652niga.html. Thanks.

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Hello NitroModels

Do you have a estimate when Item#: 93A40-13-LandingGearSet will be in? I just got the Flying Tiger kit, and I want to put the retracts in. Note that I'm a bit disappointed that you advertise that the kit has the retracts, and down below you point out it doesn't have them. You should go to Airfield and get them to include them! Other then that, the plane looks great so far (I haven't taken everything out and inspected it yet though)
Thanks!

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Nevermind, taken care of on rcdiscuss.com

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Super Chipmunk Cowling........listed on your parts page.........it has been OS for quite a while.



If they are still producing the aircraft, should they not have them?
Any chance someone could make a call, email, or even a fax to the factory to check for sure?
It is a shame........nice aircraft, good quality.........no spare parts.

So................can you use your descretion and pull a cowling for me?



Thanks,
Fred

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

yhst-17210252890263-149194

Airfield RC P51 Mustang Blue http://www.nitroplanes.com/93a275-800p51-blue-arf.html

Need the red plastic "firewall" piece, and blue spinner.

-Cameron

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

I need a cowl for my Yak 54 like this one 90A162R_Gas_Yak54-3DRed. I purchased three of these planes late last year or earlier this year. Any chance you can help?

Ray

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

This customer service sux!!!!! I have tried calling, emailing, live chat~what a joke.

It seems they want to sell planes but NO CUSTOMER SUPPORT !!!!!!

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Sigh,
I hope your wrong.... I haven't seen or heard anything from them either. I've called and posted on this forum and one other, but I haven't found the customer service email address, so I haven't emailed.

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Guys dont feel left out, I have been trying to get parts for my 64mm edf for months and keep getting the run around. And have asked about a canopy for my 120 size FW190 and still not heard from them. Needless to say I AM VERY DISAPPOINTED IN THERE CUSTOMER SERVICE

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Need parts for DYNAM GRAND CRUISER, props and spinners, when will they be available?


Larry

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

re: http://www.nitroplanes.com/90a268.html Item#: 90A268-Senorita-EP-Trainer, order # 995690.

Got this item UPS yesterday. Undamaged intact box. Lots of missing items; unacceptable for sure.

Items missing are: aluminum front wing joiner, metal rear wing joiner, bag #4 - horiz stab and elevator assembly, bag #6 - sub bag with 4 x mounting screws, Bag #7 and subbag - windshield and screws, bag #8 and sub bag A & B - Complete LG setup, also bag # 10, 11, 12, 13 and 14.

Rather pitiful performance here. You can reach me ASAP at tshafer3661 (at) charter.net.

Tom Shafer

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Just a follow up. Melissa, manager from Nitro, called with 24 hours of getting notifying email. She said she will locate the missing parts and mail them Monday. The box was sealed at factory so appears the screw up was there.

Tom

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Hello, my son and I are looking for spare parts for the Exceed J3. We would like to get a new fuselage. Also, any suggestions for another trainer I can get him forChristmas? Finally, is there a big difference in difficulty in flying a 3 channel vs 4 channel for a beginner? Thanks

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Will leave the other questions for Nitro.

Will say the Seniorita is a great trainer they have in stock. It is easy to convert from electric design to glow. I plan to cut an extra firewall from 1/8" ply and epoxy it on. You can get a motor mount at your hobby shop. You will probably be able to rig up the mount and cut the cowl to fit your 2 cycle engine. If you need a 4 cycle cowl, I got a fiberglass one on the 'net.

I would stay away from 3 channel. Not a big difference but you will just learn have to fly 4 channel later. In training, you turn with the ailerons and use the rudder rarely.

Tom

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

I know the other guy said to stay away from 4 channel, I don't know that I agree with that. For learning, a top wing that rights itself takes one of the confusing factors out, with ailerons you will loose a lot of the self - righting characteristics that you want on a early trainer. Then after a few planes, switch to ailerons. That way you get the feel a bit more before you start flying a plane that's easier to tip-stall and loose orientation with. That was why my flying friends recommended I start with a elevator/rudder plane, and hold off on the 4 channel aileron planes until I had some stick time. It sounds like he might have had a plane already, if so and he's able to fly it reasonably well, then consider the 4 ch. plane.

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Do you have any idea when the Red and White 1.20 size Gee Bee will be available again?
Al Burman

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Hi;QUestion?One of the ESCs on my new PBYbrushless version has failed!I could probably cut in a new one but would be nice to get the original as it is split with a Y to 2 ESCs etc.DOn't know if parts are avaible or how to go about ordering one and find price etc if you have them avaible?Thank you!

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Hi there Nitro ModelsI'm in need of a caopy for your Aquila ATo1. I know the plane is out of stock, but I'm hoping you might still have a replacement canopy. Please let me know if you do.
Thanks-John Reade

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Hello,

I purchased 4 of your Yak 54 3D 50-56" Nitro Planes Item#: 90A162R_Gas_Yak54-3DRed.
I am in need of a new cowl. How can I order one?
Ray

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Hello I just recieved a Seniorita EP-63" Radio 90A268-Seniorita-EP-Trainer,order #1011929 with missing parts.Bag #7 Formed and trimmed windshield with 6 holes drilled for screws,and Sub bag 6 each T2x8 PWA screws.Please advise on what I need to do to get the missing parts.

Thanks Jim.

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

where can i get replacement parts for my nitro bobcat

RE: NITROMODELS REPLACEMENT PARTS REQUEST_Post Here
 

Need a canopy for the Dynam Meteor jet, just got it today and no canopy,,,,,help!