HELP!!!!!!!!!!!!!!!!!!!!!
04-20-2005 | 07:15 PM
#1
Thread Starter
Senior Member
Joined: Oct 2003
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
From: Cherry Hill,
NJ
HELP!!!!!!!!!!!!!!!!!!!!!
What is going on with my reciever? i plug in everything turn on the radio and plug in the battery, no responce... could it be the crystal?
because i just bought this reciever today and its not working. please help me out
because i just bought this reciever today and its not working. please help me out
04-20-2005 | 07:32 PM
#2
Senior Member
RE: HELP!!!!!!!!!!!!!!!!!!!!!
It could be a bad crystal but I would make sure that the receiver is on the right shift for your transmitter.
Try using a receiver battery and pull out the ESC cable so you are only testing the elevator and rudder (or aileron) servos. Perhaps the BEC on the ESC is bad.
Good luck!
Try using a receiver battery and pull out the ESC cable so you are only testing the elevator and rudder (or aileron) servos. Perhaps the BEC on the ESC is bad.
Good luck!
04-20-2005 | 08:43 PM
#3
Senior Member
Joined: Oct 2002
Posts: 2,084
Likes: 0
Received 0 Likes
on
0 Posts
From: Winchester,
VA
RE: HELP!!!!!!!!!!!!!!!!!!!!!
I found out that for JR only the 9 channel Rx's use Dual Conversion crystals after being sold 1 at the LHS they ordered for me and it didn't work. I got a single conversion crystal and it's been fine since. I figured the LHS would get me the right type of crystal since I told them exactly what it was going into. Nope Danny at JR/Horizon Hobby knew exactly what it was.
04-20-2005 | 08:48 PM
#4
Thread Starter
Senior Member
Joined: Oct 2003
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
From: Cherry Hill,
NJ
RE: HELP!!!!!!!!!!!!!!!!!!!!!
its not the esc because i checked that on my good reciever for my gas plane. so im hoping its the crystal, and i want to know something, GWS suggested a 7.2 volt battery, im using a 8.4 volt but i am using a watt age 10 a speed controller. could the battery have killed the other reciever or the crystal?
04-22-2005 | 08:06 PM
#6
Member
Joined: Aug 2004
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
From: RICHMOND, BC, CANADA
RE: HELP!!!!!!!!!!!!!!!!!!!!!
are you conecting the battery straight to the reciever or through the esc?
if its thro the esc it should be fine
but if its straight into the reciever i think you may have burned it out
im not sure if the gws reciever can hadle it i know the cheapo 3 ch no name will burn out right away if u put over 6 volts in em
Mike
if its thro the esc it should be fine
but if its straight into the reciever i think you may have burned it out
im not sure if the gws reciever can hadle it i know the cheapo 3 ch no name will burn out right away if u put over 6 volts in em
Mike
04-22-2005 | 08:10 PM
#7
Member
Joined: Aug 2004
Posts: 75
Likes: 0
Received 0 Likes
on
0 Posts
From: RICHMOND, BC, CANADA
RE: HELP!!!!!!!!!!!!!!!!!!!!!
try flipping the crystal around and clean the ends with rubbing alcohol
did you buy a new set of crystals or just a revicer crystal?
Mike
did you buy a new set of crystals or just a revicer crystal?
Mike
04-22-2005 | 10:05 PM
#8
Thread Starter
Senior Member
Joined: Oct 2003
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
From: Cherry Hill,
NJ
RE: HELP!!!!!!!!!!!!!!!!!!!!!
yeah i bought a new crystal and i plug my battery into the esc but glacier girl helped me figure out what was wrong with it
04-23-2005 | 10:22 AM
#10
Thread Starter
Senior Member
Joined: Oct 2003
Posts: 278
Likes: 0
Received 0 Likes
on
0 Posts
From: Cherry Hill,
NJ
RE: HELP!!!!!!!!!!!!!!!!!!!!!
turns out that the ESC wat the ploblem, I got a new one from castle creations today, i sent that back last week and i was using a wattage in the mean time, so now i get to send that back
