Community
Search
Notices
RC Car General Discussions This forum is for all general discussions related to radio control cars. Check forums below for more specific categories if applicable.

help!!!

Thread Tools
 
Search this Thread
 
Old 07-07-2003 | 03:37 PM
  #1  
dan1220's Avatar
Thread Starter
My Feedback: (2)
 
Joined: Apr 2003
Posts: 1,260
Likes: 0
Received 0 Likes on 0 Posts
From: Toledo, OH,
Default help!!!

ok, I was out running my truck, and I could tell that it wasnt running very well, after a couple minutes, smoke started coming from the head. I have never seen that before. a few minutes later, the engine died. I dont know what was happening. Also, I dont think my brakes work. The servo doesnt move when I apply the brakes. Any advice would be greatly appreciated.
Old 07-07-2003 | 04:28 PM
  #2  
dan1220's Avatar
Thread Starter
My Feedback: (2)
 
Joined: Apr 2003
Posts: 1,260
Likes: 0
Received 0 Likes on 0 Posts
From: Toledo, OH,
Default help!!!

no one?
Old 07-07-2003 | 04:29 PM
  #3  
Rex2342's Avatar
Senior Member
 
Joined: Apr 2003
Posts: 1,835
Likes: 0
Received 0 Likes on 0 Posts
From: East Pittsburgh, PA,
Default help!!!

Sounds like it's to lean and you need to charger the batteries in the reciever.
Old 07-07-2003 | 05:12 PM
  #4  
Senior Member
My Feedback: (1)
 
Joined: Feb 2003
Posts: 280
Likes: 0
Received 0 Likes on 0 Posts
From: ABQ, NM
Default help!!!

is your head on tight
Old 07-07-2003 | 09:52 PM
  #5  
dan1220's Avatar
Thread Starter
My Feedback: (2)
 
Joined: Apr 2003
Posts: 1,260
Likes: 0
Received 0 Likes on 0 Posts
From: Toledo, OH,
Default help!!!

well, My head is tight, the batteries ar good, and Im running pretty rich. THe smoke is gone, but it seems like when my engine stops (by itself) I cannot start it untill it cools off a bit. I dont have a temp gun, but I am running rich.
Old 07-07-2003 | 10:00 PM
  #6  
Senior Member
My Feedback: (1)
 
Joined: Feb 2003
Posts: 280
Likes: 0
Received 0 Likes on 0 Posts
From: ABQ, NM
Default help!!!

I have that same problem if and when it dies i cant start it up for a few min, but what i started doing is blowing the 2 fuel lines clear of fuel, then re-priming it! STARTS RIGHT UP!!
Old 07-07-2003 | 10:25 PM
  #7  
dan1220's Avatar
Thread Starter
My Feedback: (2)
 
Joined: Apr 2003
Posts: 1,260
Likes: 0
Received 0 Likes on 0 Posts
From: Toledo, OH,
Default help!!!

how do you blow them? wouldnt that take longer?
Old 07-07-2003 | 10:26 PM
  #8  
dan1220's Avatar
Thread Starter
My Feedback: (2)
 
Joined: Apr 2003
Posts: 1,260
Likes: 0
Received 0 Likes on 0 Posts
From: Toledo, OH,
Default help!!!

hey Rex!!

every time i see you avatar it is showing more skin Cant wait till next week!!
Old 07-08-2003 | 04:12 AM
  #9  
Senior Member
My Feedback: (1)
 
Joined: Feb 2003
Posts: 280
Likes: 0
Received 0 Likes on 0 Posts
From: ABQ, NM
Default help!!!

Hehe! Just blow them back into the fuel tank or take off the fuel line and blow the stuff out, then put the fuel line back on, prime it and start it. Just try it.

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are On



Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service

Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.