RCU Forums

RCU Forums (https://www.rcuniverse.com/forum/)
-   RC Flight Simulator Software (https://www.rcuniverse.com/forum/rc-flight-simulator-software-138/)
-   -   AFP blender video (https://www.rcuniverse.com/forum/rc-flight-simulator-software-138/1927985-afp-blender-video.html)

STLPilot 06-23-2004 08:38 AM

AFP blender video
 
Someone was asking about whether AFP could do blenders. Easily with any of the 3D planes. This one is with the Chip Hyde Ulty.

This is a 30 FPS output video, actual FPS on sim was 175 FPS.

[link=http://www.flybuder.com/aeroflyvids/blender.wmv]Click here to view video 11MB WMV[/link]

ptarp 06-23-2004 09:04 AM

RE: AFP blender video
 
Thanks! Ask and ye shall recieve :)

I'm at my brother's house right now with slow dialup connection, so I'll wait to watch it until later.

You said you can easily do a blender with any of the 3D planes? If so, I must be doing something wrong during executing the blender, this is how I am trying...

After gaining sufficient altitude...
Chop throttle, point nose straight down
Give full left aileron
After about three rotations, add full right rudder and full down elevator
The plane should immediately enter an inverted flatspin, add some throttle to tighten it up.

This procedure was taken from...
http://horizon.hobbyshopnow.com/Prod...2-ART.asp?pg=6
and worked perfect for my Kyosho Cap in "real life"

How do you do it?

Spacey 06-23-2004 09:19 AM

RE: AFP blender video
 
You're on the right track. Just do not forget to let go of the ailerons on some birds. Some only require a little bit of aileron to flatten it out. You gotta feel it out.

STLPilot 06-23-2004 09:26 AM

RE: AFP blender video
 
You cannot use full deflection on all the planes.

The best thing to do is to learn a inverted flat spin on the plane you want to do a blender. Not on all planes do you put full deflection to sustain an inverted flat spin. On some planes it's only half of the servo travel or the rudder, ailerons and elevator. Or a mix of the 3.

But you are basically right though. You enter a blender nose down rolling in either direction with a none or just a little throttle. Then you enter an inverted flat spin in the same direction of the roll. First you master the inverted flat spin on a particular plane, then you add the pitch down roll.

Spacey 06-23-2004 09:37 AM

RE: AFP blender video
 
Oh yeah! Nice description Dion. Nice flying as well, are we going to have a contest to see who can end it the lowest? :D

ptarp 06-23-2004 10:10 AM

RE: AFP blender video
 
Thanks for the speedy responses guys :) I can't wait to get home and put some hours on AFP :) I was up till about 3:00 last night doing so:D

STLPilot 06-23-2004 03:59 PM

RE: AFP blender video
 
HAHA! Spacey I was drinking a cup of coffee while I was doing that. You wanna go low? Bring it on!

BouyanT_PooP 06-23-2004 05:08 PM

RE: AFP blender video
 
i'd like to see this!!! :D

Spacey 06-24-2004 03:19 AM

RE: AFP blender video
 

ORIGINAL: STLPilot

HAHA! Spacey I was drinking a cup of coffee while I was doing that. You wanna go low? Bring it on!
LOL....I knew there was something funny going on there! What do you put in your coffee? :D
I think I got myself into trouble here. :)

iflynething 06-26-2004 12:18 AM

RE: AFP blender video
 
I would say that was pretty low STLPilot when you just recovered just above the ground and then the gear hit the deck.....I'd have to say that that is pretty close......

STLPilot 07-27-2004 06:43 AM

RE: AFP blender video
 
Hey Spacey, where's your video?? :D

Spacey 07-27-2004 07:03 AM

RE: AFP blender video
 
Dude if I get over this hang over I gots today I'll make something tonight and send it to ya tomoz early early. :)

Spacey 07-27-2004 07:40 AM

RE: AFP blender video
 
Oh Dion! I just thought of something else. Have you ever tried a hover landing on one of the tables under the shelter thingy on the desert scenery? I did a couple of nights back but with not much success. Maybe that can be our next challenge. lol


All times are GMT -8. The time now is 05:47 PM.


Copyright © 2026 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.