Laser 3D printed turbine accessory bracket set.
#1
Thread Starter
Laser 3D printed turbine accessory bracket set.
Hello all.
I would like to show you a new product I have been working on for a while.
This is a set of laser 3D printed turbine accessory brackets and clips for your favorite engine.
All the brackets and clips are CAD designed and CAM produced from the best material to 50 micron resolution.
The brackets come in black color to fit possible carbon fiber trays and the clips in grey color for Krylon make-it-stone finish.
It comprises of:
An ECU tray with retaining tabs and 4 countersink holes, coming with its countersink screws.
A fuel pump holder, with four retaining screws, two being used to squeeze the pump in the bracket.
A fuel valve holder. The valves sit side by side and are fastened through with two 2-56 long screw. Two countersink holes and screws come with the set to fasten the holder.
An I/O board holder that serves 2 purposes. It isolates the board from the accessory plate, thus enabling the use of carbon fiber sheeting if required and also lifts the board to avoid damaging the components weldings. This elevated position also facilitates the extraction of the RJ-11 plug from the socket. This comes with a set of 4 sheet metal screws
One 4 mm PYCABS clip for the fuel tubing.
One 2.6 mm PYCABS clip for the power wires
A set of 4 EZ PYCABS clips
The set allows very clean installations.
This is available for the BF-Turbines B-100F, B-300F, Behotec JB-220 and any C6 ECU controlled Jetcat engine.
Here is the product page:
http://www.ultimate-jets.net/collect...es-bracket-set
I would like to show you a new product I have been working on for a while.
This is a set of laser 3D printed turbine accessory brackets and clips for your favorite engine.
All the brackets and clips are CAD designed and CAM produced from the best material to 50 micron resolution.
The brackets come in black color to fit possible carbon fiber trays and the clips in grey color for Krylon make-it-stone finish.
It comprises of:
An ECU tray with retaining tabs and 4 countersink holes, coming with its countersink screws.
A fuel pump holder, with four retaining screws, two being used to squeeze the pump in the bracket.
A fuel valve holder. The valves sit side by side and are fastened through with two 2-56 long screw. Two countersink holes and screws come with the set to fasten the holder.
An I/O board holder that serves 2 purposes. It isolates the board from the accessory plate, thus enabling the use of carbon fiber sheeting if required and also lifts the board to avoid damaging the components weldings. This elevated position also facilitates the extraction of the RJ-11 plug from the socket. This comes with a set of 4 sheet metal screws
One 4 mm PYCABS clip for the fuel tubing.
One 2.6 mm PYCABS clip for the power wires
A set of 4 EZ PYCABS clips
The set allows very clean installations.
This is available for the BF-Turbines B-100F, B-300F, Behotec JB-220 and any C6 ECU controlled Jetcat engine.
Here is the product page:
http://www.ultimate-jets.net/collect...es-bracket-set
Last edited by olnico; 03-03-2015 at 11:36 AM.
#3
Thread Starter
#5
Thread Starter
#6
My Feedback: (2)
Oli,
I'll start off with dimensions for the Jeti Rx that I have.
Jeti EX R11 EPC Rx
51.50 x 25.00 x 11.00mm
The connectors plug into both ends of the Rx, on the 25x11 faces. These is a 1.50mm edge distance to the servo connector openings. Hopefully the link to a picture of the Rx helps.
http://file.espritmodel.com/radio/re...ex-r11-epc.jpg
Jeti EX R14 Rx
62.70 x 38.20 x 16.50mm
You need to avoid an area 13.5 - 20.5mm in from the end along the 62.7mm edge as this is where the 2 antennas exit the case.
http://file.espritmodel.com/radio/re...eti-ex-r14.jpg
Jeti Telemetry Sensor GPS MGPS EX
50.00 x 30.50 x 13.00mm
http://file.espritmodel.com/telemetr...sensor-gps.jpg
Paul
I'll start off with dimensions for the Jeti Rx that I have.
Jeti EX R11 EPC Rx
51.50 x 25.00 x 11.00mm
The connectors plug into both ends of the Rx, on the 25x11 faces. These is a 1.50mm edge distance to the servo connector openings. Hopefully the link to a picture of the Rx helps.
http://file.espritmodel.com/radio/re...ex-r11-epc.jpg
Jeti EX R14 Rx
62.70 x 38.20 x 16.50mm
You need to avoid an area 13.5 - 20.5mm in from the end along the 62.7mm edge as this is where the 2 antennas exit the case.
http://file.espritmodel.com/radio/re...eti-ex-r14.jpg
Jeti Telemetry Sensor GPS MGPS EX
50.00 x 30.50 x 13.00mm
http://file.espritmodel.com/telemetr...sensor-gps.jpg
Paul
#8
Thread Starter
#10
Thread Starter
Jeti GPS:
On the R14, the top of the clip extends on the receiver top by 1.9 mm at the location of the servo plugs. Please check if this still clears the opening.
On the R14, the top of the clip extends on the receiver top by 1.9 mm at the location of the servo plugs. Please check if this still clears the opening.
Last edited by olnico; 03-06-2015 at 02:45 AM.
#13
Thread Starter
Send me your address, I'll ship one prototype of each to you. If they work we'll talk what you'd like to buy.
The product page is here;
http://www.ultimate-jets.net/collect...receiver-bases
The product page is here;
http://www.ultimate-jets.net/collect...receiver-bases
#20
Thread Starter
#23
Thread Starter
#24
Thread Starter