William H

YOu think I need an engine rebuild just for that one disk that is what I meant it is moving right to left is the normal?GMAC?

gmac4826

iw asnt talking about that. if oyu look it says 'rc10gtplusr2r:' so that is who i was talking to.

gmac4826

william:
if it doesnt affect performance or anyhting like that or there isnt excessive wear i wouldnt worry about it.

William H

Oh man sorry bout that I thoought that was you!!!SORRY MAN!!!!

William H

How can you tell if they are warn and will they still work?

gmac4826

when they are about 3/4 to 1/2 of the origonal width.

William H

Is it normal for the right rear well to spin back ward when I put on the brakes?

gmac4826

i=not really but i dont think it matters.

William H

What might you think it is doing that and do you mind me asking all these questions?

gmac4826

no i dont mind. i think its that when you hit the brakes the wheels stop spinning forward and they spring back.

William H

Yeah That is right but is that normal?You hit the nail on the head!!!

William H

gmac I like that picture on the top left corner where you get them?

gmac4826

it isnt designed to do that but it does and you live with it. and since you should only run with your car on the ground i wonder how you notice this...

electricfan

My Feedback: (1)

whenever i am idling my gt then give it full throttle, it hesitates, then goes to full throttle. i keep getting "richen the low end", but it makes things worse, so i lean it and it gets better. does this happen to anyone else? its the associated 15 engine

gmac4826

i dont know why people were telling you tor richen the low end but if you have that problem you are supposed to lean it. but remember, not too lean or you will burn up your engine

Roundy79

I've had my RC10GT now for almost a year and I've been able to run with the best of them. I run a Fantom '03 .15 non p/s, Robinson Racing Transmission gears, as well as bell and spur gears. I've upgraded the turnbuckles to titanium Lunsford turnbuckles and RPM rod ends. I also threw on a full set of ball bearings from BOCA (green sealed), aluminum hop-up's including some of the best aluminum rims I've ever seen or ran from RC-Parts, and finished the whole show with a JR XR2 Radio.

I've finished in the Top 3 Modified class at my local track for the past six months straight. I'm also the only one with a GT at the track. Most are running Traxxas Rustler's with the new 2.5, XXX-NT, and a few other brands in-between. They all use to pick on my GT at first, but now they can't wait to try and get me at the finish line.....don't worry though Gt fans...only in my dust!

I've tried all the products and hop-ups...let me know if I can help.

rc10gtplusR2R

dont let this die we need to stand up for are rc10gt so stand up post some more on here ok

rc10gtplusR2R

dont let it die

rc10gtplusR2R

please rc10gt people dont let this thread die ok it is i will start a new one

dan1220

My Feedback: (2)

on my rc10gt, I just got running, and there is a buzzing sound when the truck rolls. the engine is not started though? what is the prob?

gmac4826

the electronics make that noise on my xxx-nt.

dan1220

My Feedback: (2)

no, every thing is off, but when I roll it on the ground, it buzzs.

gmac4826

pprobably something rubbing.

William H

I think it might be the clutch it might be lose.Check to see if everything is on it.If that does not work it is the engine.

jsmcbrayer

Master,
I know this is completly off the subject of your thread, but I just watched a show about the city of Dubai and the canal city they're building. Seems like a cool city. They also showed that awsome boat shaped hotel on that little man made island. That hotel is sweeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeet! I wish I had enough money to stay there for a week!