RE: Black Magic v2 builder's thread! *Updated*
 

Melissa says thanks very much about the carbon work :D (She's gotten very good at making those)

As for a composite kit.....it's a ways off. I can't even give an estimate, because I really haven't started it yet. I know I want to do one, and have a ton of ideas about it, but I just haven't made it that far yet.

But it's in the works, I just want it to be one of those that pulls out all the stops if I'm going to do it. However with that being said, my personal planes will probably be wood!

-Mike

RE: Black Magic v2 builder's thread! *Updated*
 

Hey Mike,

The kit is going together very well . Quicker than I thought. If I would have gotten the right wing tube and stab tubes. I think this plane may have made it to the Nats. The fuse is almost done.

Buddy

RE: Black Magic v2 builder's thread! *Updated*
 

PICTURES!!!!! Post pics!!! ;)

Just a few detail shots. Couple pics of the inside, and take special note of the stiffener at F-4. Also the air dam which I now consider standard equipment.

-Mike

RE: Black Magic v2 builder's thread! *Updated*
 

And a couple more....

RE: Black Magic v2 builder's thread! *Updated*
 

Hey Mike ,

Looks good !! but what is with the funny looking engine , and green tubing and fuel tank...
Hard to run electric that way :)

Scott Anderson

RE: Black Magic v2 builder's thread! *Updated*
 

Here's some pic's. Can you post a clean shot of the belly pan. I am having a heck of time trying to get it to line up. I need to slow down on this project. I've made some minor errors. Which cost me even more time. I work alot of hours durning the week so I wont even touch it again till Saturday evening.


Willie B.

RE: Black Magic v2 builder's thread! *Updated*
 

Ok. Lemme dig and see what I can find. I heard Dean had the same problem, which way is it "off"? I garauntee it's something simple (usually is).

This is all I can find right off the bat, I have a bazillion pics.

I do have mine off of #1 right now, so is there any specific area you need to see?

-Mike

RE: Black Magic v2 builder's thread! *Updated*
 

HI Willie b,

I am about to post a bunch of photo's I'll try to get some of the belly, since mine isn't painted yet it they might be clearer than Mikes finished plane.

Can you tell me what you are looking for....

My canopy is drying - I'll trim it and do the the photo session....

dean

RE: Black Magic v2 builder's thread! *Updated*
 

Oh and here ya go Scott, electric Black Magic pics [8D]

Mine are going to have to wait a while.

-Mike

RE: Black Magic v2 builder's thread! *Updated*
 

Yeah, a lot of mine are blurry. I'll take more when I get back into full tilt building mode (after the Nats).

Anything you guys want to see, I either have it or I'll take it. And if not, Dean probably has GOOD pics. LOL

-Mike

RE: Black Magic v2 builder's thread! *Updated*
 

I need to see where it mates to the lower deck and along the frame sides. Mine sits a little low. I will post some pic's later this week.

Thanks For The Help,
Buddy.

RE: Black Magic v2 builder's thread! *Updated*
 

Buddy,

The plane is designed so that you sheet your top around the nose, and rough sand it first.

Then mount the engine.

Sand a lip for the cowl to seat onto the fuse, and slide the cowl on over the engine. The cowl must be trimmed at the rear about 1/4"-3/8", and the distance from the spinner back plate to the firewall is about 6 3/8". Leave a small clearance between the spinner and cowl of about 1/16".

It is common practice to have to sand the bottom there and "raise" the cowl very slightly. This will leave a slight gap between the cowl and belly pan at the engine compartment.

After the cowl is glued on, take a lagre block sander and work the bottom of the fuse so it fits better. you can still leave a slight gap, because of the way the belly pan is shaped, when you tighten your front screw it will pull it all tight.

I hope that made sense. if you need more help, you know my #.

-Mike

PS I'm still looking for belly pan pics...

RE: Black Magic v2 builder's thread! *Updated*
 

Oh and if you mean it's low where it meets the rear belly core, pffft lay down a piece of 1/16" balsa on the fuse and stringers and sand to fit. I love wood.

-Mike

RE: Black Magic v2 builder's thread! *Updated*
 

Works for me problem solved. The only way I could see solving my problem is what you desribed. If I flexed the belly pan to raise up to meet the rear belly core then It through everything else off.

Thanks Buddy

RE: Black Magic v2 builder's thread! *Updated*
 

Hi All,

I am trimming my canopy now, just had to share this picture of the big mess in my shop - remember back on page 6 or so.... how nice and neat everything was..

well forget about it. this place is a toxic mess.....

Had a busy few days here - the plane build is done. It's in the bones now.

I need to trial fit the electronics and start finish....

yey-haw...

about to crack another beer! (#150 I think)

I'll post some pictures once I clean up this dump....

Cheers!

dean

RE: Black Magic v2 builder's thread! *Updated*
 

pWn3D!!!


LOL

Post those pics!

-Mike

RE: Black Magic v2 builder's thread! *Updated*
 

I'm printing those pictures of the trashed workshops. Good to know someone else besides me can tear one up.

Mike will e-mail you later about the Black Magics

Dennis

RE: Black Magic v2 builder's thread! *Updated*
 

Hi All,

Here are some pics, the build is basicly finished. I have equipment and mounts next. But I am happy happy happy !! This is one bad mother !!!

The airframe fully asambled in these photos is at 4 lbs 13.9 oz - that's the complete airframe. Not sure where it's going to end up at but this thing is really really big, really strong and very light....

the cowl and belly went on nice and the canopy fit is tight.

Dang this beer is tasting GREAT !!!!

loving this plane, man it's awesome !!! it's beautfull !! loving it!!!

cheers, Dean

RE: Black Magic v2 builder's thread! *Updated*
 

just cracked beer #152

RE: Black Magic v2 builder's thread! *Updated*
 

duplicated one of the images...

here is the one of the scale

RE: Black Magic v2 builder's thread! *Updated*
 

HI Mike,

I had to look up "pWn3D!!! " http://www.urbandictionary.com/define.php?term=pwn3d

I think you where implying definition #2.....

about to crack beer #153....

man, life is good, I am down here in the basement, it's 12:45 am... with my new plane, watching a John Wayne flick on the tube, drinking Heineken's....

I think I might just sleep down here tonight.....

RE: Black Magic v2 builder's thread! *Updated*
 

yes, it was indeed definition #2. Sorry, throwbacks to my old days of Ultima Online and Team Fortress Quake.....

Ahh yes, Heineken...the official beer of the Black Magic! I'm only on #6 tonight, and am stopping right in the middle of rebuilding my second engine. Must...get...sleep.........and practice, yes, much practice....

Dean, fantastic job man!!!!!!! You might get a dragon shirt for that one. Do that finish right, make us proud!

Wait, I'm having a vision.....it's foggy....but clearing...I see.....your future....it's wood...no wait....SANDPAPER!!!!!!! AAAARRRRGGGHHHH!!!!!!!!

LOL have fun finishing that beast. I'll be at Ga Jets trying to get some much needed practice. Y'all got my # iffin ya needs me!

-Mike

RE: Black Magic v2 builder's thread! *Updated*
 

Oh yeah one more thing.....the top of your tail/rudder, is that cocked backwards or is it just the pic? It's supposed to be parallel with the center line of the fuse......

Just curious. Nighty night all. Good night Johnboy!

-MikeBob

RE: Black Magic v2 builder's thread! *Updated*
 

yea that is the pic, I shot it with my 16mm fisheye lens.... no worries it's parallel to the centerline.... look how weird the stab looks too....

RE: Black Magic v2 builder's thread! *Updated*
 

Dean,

Any chance you can post pics of wing fixing bolts, I think Mike bolts through the end of the wing bolts in the wings instead of using wing fixings on the socket at the fuselage join. I see there are twin wing adjusters front and rear any advantage to this ?

Thanks

Ian