Where do I buy Carbon Tube in Canada/USA?
Hi guys...
Where in the world can I buy 10mm OD (8mm ID) Carbon tube for a mast in Canada or the US? I need 2m (6')(72")(2000mm) in a single piece. Thanks! Goose |
RE: Where do I buy Carbon Tube in Canada/USA?
Goose,
You may try Adrian Olson's GRP Model Yachts in California @ www.modelyachting.com. They have hardware, masts, rigging etc for the Wheeler class yachts which are large! Adrian's e-mail is [email protected] Jeff |
RE: Where do I buy Carbon Tube in Canada/USA?
Great!
Thanks Jeff, I will start there. :D Goose |
RE: Where do I buy Carbon Tube in Canada/USA?
You may have a hard time finding a 72"small diameter tube. But a inside ferrule joint can work well. Wrapped carbon fiber is very stiff if desired. I've used 8P tube described at http://www.skyburner.com/skyshark/p-series.html
Also take a look at the RC mast tube available at http://www.midwestmodelyachting.com/CFMastTubes.asp |
RE: Where do I buy Carbon Tube in Canada/USA?
Thanks Jaelon...
I am reading up on ferrule joints now and that seems like a viable solution. What did you use for the ferrule? Cheers Goose |
RE: Where do I buy Carbon Tube in Canada/USA?
I used another piece of hollow carbon tube whose OD fits snugly in the ID of the main mast pieces. Solid carbon tube would be a stronger ferrule but probably not necessary. A little epoxy could be added for permanent joining.
|
RE: Where do I buy Carbon Tube in Canada/USA?
Cool, thanks...
Given the length of the mast, I am thinking about a two-piece arrangement. What do you guys think about a metal sleeve over one end and the ferrule epoxied into the other piece as a solution? Is there a better/easier way to do it? Cheers Goose |
RE: Where do I buy Carbon Tube in Canada/USA?
V6GOOSE:
I actually used carbon to carbon with enought medium cyano glue, and it becomes harder than metal. In fact i just drilled a 1/8" hole at the top of the mast and cyanoed the 1/8" tube for the crane. it never moved!!. try to get a carbon tube wich its inner diameter fits another Outside diameter in a carbon tube. most of the Us stores has many carbon tube sizes, but sometimes they do not have diameters that allow the "telescopic2 effect. i found carbon spars at http://www.r2hobbies.com/products.php?cat=136 and they are telescopic, it means the smaller fits the inner dia of the bigger. just use a 4" inner tube as a ferrel and you are done!!! Hope this can help, prices looks great too. Tato Lazo CHI 272 |
RE: Where do I buy Carbon Tube in Canada/USA?
Excellent, thanks a lot Tatolazo...
|
RE: Where do I buy Carbon Tube in Canada/USA?
We use carbon tubes and ferrules all the time in stunt kites, up to 13mm diameter. Contact [link=http://www.chicokites.com/]GWTW-kites [/link] and ask Steve or Chris about the specific diameter of tube you need, and tell them you'll need a ferrule for joining the two pieces
|
RE: Where do I buy Carbon Tube in Canada/USA?
I've used R2hobbies, they were excellent and quick ~ well impressed
Rgds AndyT |
RE: Where do I buy Carbon Tube in Canada/USA?
Good one!
R2H is cheap too! Thanks guys... Goose |
RE: Where do I buy Carbon Tube in Canada/USA?
|
RE: Where do I buy Carbon Tube in Canada/USA?
Hi Dias...
Thanks for that. I had seen this and unfortunately the 10mm OD Carbon tube I'm after only comes in 60" lengths. My mast is around 1825mm (~72") long so a splice or ferrule is needed. Cheers Goose |
All times are GMT -8. The time now is 06:31 PM. |
Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.