1/6 SCALE SOPWITH PUP "Build"
#103
Senior Member
Thread Starter
My Feedback: (5)
Join Date: Oct 2004
Location: Horse Shoe,
NC
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/6 SCALE SOPWITH PUP "Build"
The Engine is from Hanger 9 and fits perfectly inside the cowl, tomorrow I plan to fiberglass the inside of the cowling and affix the faux engine, to cowling. I also received my servos they will also be installed tomorrow as well.
For comparison, Standard Hitec HS311 and Mini HS-225MG Quarter on top of mini
For comparison, Standard Hitec HS311 and Mini HS-225MG Quarter on top of mini
#105
RE: 1/6 SCALE SOPWITH PUP "Build"
Thanks for the dimension. I can use that same Hanger9 engine in my Pup too. Its cowl is slightly smaller at 6-1/2".
I can relate to the joy of seeing packages arrive. It can be addicting. I am currently awaiting a few things myself (a half pilot, wheels, servo extensions).
I can relate to the joy of seeing packages arrive. It can be addicting. I am currently awaiting a few things myself (a half pilot, wheels, servo extensions).
#106
Senior Member
Thread Starter
My Feedback: (5)
Join Date: Oct 2004
Location: Horse Shoe,
NC
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/6 SCALE SOPWITH PUP "Build"
OK, Christmas break is over time to get back in my shop, by this weekend I will have clean my shop from stem to stern and if anything gets on my nerves is not being able to find something or the inability to lay something down without turning something else over, so cleaned up it will get. My engine is supposed to be in this Friday and I have servos, and a faux engine to mount and various other things to complete, we also have 1-8 inches of snow in the forecast with temps around 0 and a wind chill of -15 good day to stay in doors wouldn’t you say. Hopefully I will be back on track by this weekend.
#107
RE: 1/6 SCALE SOPWITH PUP "Build"
Jeff, I know just how you feel. At times my shop gets so bad that a "lose" a tool just as soon as I set it down. I've thoroughly cleaned my shop twice during the Snipe build -- which I hope to get back to immediately upon my return to Japan.
#112
RE: 1/6 SCALE SOPWITH PUP "Build"
Certainly in that size, in fact I just ordered a pair of the Flairs for my 1/6th scale Pup although I already had a pair of the Williams Bros.
I think in some sizes the Williams Bros are fine.
I think in some sizes the Williams Bros are fine.
#113
Senior Member
Thread Starter
My Feedback: (5)
Join Date: Oct 2004
Location: Horse Shoe,
NC
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/6 SCALE SOPWITH PUP "Build"
Ok, not much has been accomplished, but I have managed to get the aileron Servos mounted.
Servos are mounted on 1/16 ply and attached to 1/4x1/2 pine blocks. The hatch has been cut undersize to accommodate the covering.
Servos are mounted on 1/16 ply and attached to 1/4x1/2 pine blocks. The hatch has been cut undersize to accommodate the covering.
#115
Senior Member
Thread Starter
My Feedback: (5)
Join Date: Oct 2004
Location: Horse Shoe,
NC
Posts: 121
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/6 SCALE SOPWITH PUP "Build"
The Servos I used are Hitec HS-225BB http://www.hitecrcd.com/servos/show?name=HS-225BB
I may have placed them in the wrong position, the plans call for them to be forward against the main spar, I was thinking short throw and placed them as far aft as I could. This may cause me to add weight to the front to counter the position of the servos.
I will use only two servos in the lower wing and connect the upper via a rod, not to scale but this is per the plans, trying to keep things simple.
I will use a 6v 1650ma Flight pack.
I may have placed them in the wrong position, the plans call for them to be forward against the main spar, I was thinking short throw and placed them as far aft as I could. This may cause me to add weight to the front to counter the position of the servos.
I will use only two servos in the lower wing and connect the upper via a rod, not to scale but this is per the plans, trying to keep things simple.
I will use a 6v 1650ma Flight pack.
#116
My Feedback: (1)
RE: 1/6 SCALE SOPWITH PUP "Build"
Where did everybody Go??? No posts since 1/14/21008. I have just read all 115 posts and all of a sudden they stopped?? Flyer Jeff, should be about finished by now? I hope all is well?
I am about to order this model as my first full build. I have 10 ARF's and think it's time to build a plane. I would like to add a WW I Warbird and the Balsa USA 1/6 scale Pup looks perfect. I have an OS 46 and 50 engine as well as all the radio gear.
By the way Jeff I have 150' of Garden Railroad in my backyard. Retired life is Great
I am about to order this model as my first full build. I have 10 ARF's and think it's time to build a plane. I would like to add a WW I Warbird and the Balsa USA 1/6 scale Pup looks perfect. I have an OS 46 and 50 engine as well as all the radio gear.
By the way Jeff I have 150' of Garden Railroad in my backyard. Retired life is Great
#119
Join Date: Dec 2005
Location: Verona, ITALY
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/6 SCALE SOPWITH PUP "Build"
[quote]ORIGINAL: TomTreese
Where did everybody Go??? No posts since 1/14/21008. I have just read all 115 posts and all of a sudden they stopped?? Flyer Jeff, should be about finished by now? I hope all is well?
I am about to order this model as my first full build. I have 10 ARF's and think it's time to build a plane. I would like to add a WW I Warbird and the Balsa USA 1/6 scale Pup looks perfect. I have an OS 46 and 50 engine as well as all the radio gear.
By the way Jeff I have 150' of Garden Railroad in my backyard. Retired life is Great
your engine for balsa usa pup 1/6 has too much power for this model you can use on flair pup
#120
Junior Member
Join Date: Aug 2004
Location: Everett,
WA
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/6 SCALE SOPWITH PUP "Build"
I just discovered this one on the Balsa USA website. Having just finished a 1/6th Tigermoth (an old Pilot kit), I'm looking at this one now (yeah, like I need another project,... but...). I'm very interested, and will be patiently waiting for more posts. Btw, I see B-USA now has a 1/6 Nieuport,.. I like the Pup better. "More posts please".
#122
Join Date: Dec 2005
Location: Verona, ITALY
Posts: 271
Likes: 0
Received 0 Likes
on
0 Posts
RE: 1/6 SCALE SOPWITH PUP "Build"
ORIGINAL: skyboy500
More... More!
I have an OS-FS70 NIB looking for a home!
Curious if it would be too much for the 1/6 Pup...
More!
More... More!
I have an OS-FS70 NIB looking for a home!
Curious if it would be too much for the 1/6 Pup...
More!
#124
My Feedback: (26)
RE: 1/6 SCALE SOPWITH PUP "Build"
ORIGINAL: eyeofra1678
I have a O.S 40 4c that needs a home this might be it
I have a O.S 40 4c that needs a home this might be it
I think the largest engine I would consider would be a surpass .52 or a Saito .56. The .72 would be way too much.