RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: uniLIGHT
Showing results 1 to 16 of 16
Search took 0.06 seconds.
Forum: RC Jets
02-22-2018, 02:54 AM
Replies: 160
Views: 60,369
Posted By uniLIGHT

Hi, and try to use a different USB cable and/or...

Hi, and try to use a different USB cable and/or on another PC. Sometimes other devices conflicts with the serial USB port. If no difference, then send it to us for checking please.
Forum: RC Jets
10-16-2017, 12:10 PM
Replies: 160
Views: 60,369
Posted By uniLIGHT

Hi, A little bit epoxy is the safer way....

Hi,

A little bit epoxy is the safer way. Easier to handle and adjust, better compensate temperature differences and no risk of fogging the lense. Additional you can use a small stripe of tape...
Forum: RC Jets
06-20-2017, 05:46 AM
Replies: 160
Views: 60,369
Posted By uniLIGHT

Yes, the gear dependend landing light is bit a...

Yes, the gear dependend landing light is bit a bit "advanced" stuff. But there is a lot possible with this kind of programming and modern transmitters. And the standard controlling by a 3-position...
Forum: RC Jets
06-19-2017, 10:10 PM
Replies: 160
Views: 60,369
Posted By uniLIGHT

Hi, yes you are missing something :-) The servo...

Hi, yes you are missing something :-)
The servo 1 & 2 are outputs to control dropout lights or similiar. Landing lights should be programmed and selected by your transmitter same as the other light...
Forum: RC Jets
05-28-2017, 03:19 AM
Replies: 8
Views: 1,041
Posted By uniLIGHT

Hi Dan, There was never a firmare update for...

Hi Dan,

There was never a firmare update for the 8-channel controller :-)

Different COM ports are possible, depends on the USB driver chip. This might be changed in a production lot, But it is...
Forum: RC Jets
06-27-2015, 10:45 PM
Replies: 3
Views: 1,426
Posted By uniLIGHT

Hi, Yes, the higher voltage needs the...

Hi,

Yes, the higher voltage needs the dedicted resistor additionally and anywhere in the wire of the lamp - it's quite easy. Sure the resistors are not the most sophisticated way to make it, but...
Forum: RC Jets
06-27-2015, 10:39 PM
Replies: 160
Views: 60,369
Posted By uniLIGHT

Hi and sorry for the late reply, we try to help...

Hi and sorry for the late reply, we try to help on threats like that as well but not looking in here each day. First many thanks for the good feedback, we try the best to get the perfect solution for...
Forum: RC Jets
02-23-2015, 01:01 PM
Replies: 11
Views: 6,371
Posted By uniLIGHT

Hi, Maybe I can help with some pics from...

Hi,

Maybe I can help with some pics from drawing the tip caps, I found it quite easy ;-)
But it is much easier when you have help from two more hands...
...
Forum: RC Jets
02-07-2015, 03:54 PM
Replies: 259
Views: 31,020
Posted By uniLIGHT

I can confirm that the lights are made for our...

I can confirm that the lights are made for our aircrafts, so the heat generation is fine for usual flight times 6-10 minutes but not for exhibition long time use. The cheaper standard parts has a...
Forum: RC Jets
01-09-2015, 03:45 AM
Replies: 9
Views: 3,935
Posted By uniLIGHT

Hi and sorry for the late pubilc response, we...

Hi and sorry for the late pubilc response, we already talked by mail. But to answer this post, basically the "search for reviewer" phase is gone, several project are in work now :-)

But of courese...
Forum: RC Jets
10-23-2014, 01:54 PM
Replies: 9
Views: 3,935
Posted By uniLIGHT

Correct, the heat dissipation is the biggest...

Correct, the heat dissipation is the biggest problem for these power LEDs. Usually a landing light is for landing and not for the full flight - but it looks so cool ;-)

As Ixfly said, the 4W...
Forum: RC Jets
10-22-2014, 01:48 PM
Replies: 9
Views: 3,935
Posted By uniLIGHT

A usual light system will consume 1.5-2.5 ampere....

A usual light system will consume 1.5-2.5 ampere. So a small battery of 1500mAh will work for a normal day with some flights. But of course all this will depend on the used light power and selected...
Forum: RC Jets
10-21-2014, 12:04 PM
Replies: 9
Views: 3,935
Posted By uniLIGHT

uniLIGHT.at is searching reviewers...

We are a young company based in Austria and specalized on very high power and quality aircraft lighting systems. Our uniLIGHT products has been established since the last year in central Europe with...
Forum: User Product Reviews
10-21-2014, 11:25 AM
Replies: 5
Views: 1,021
Posted By uniLIGHT

Ah, some parts are maybe usable, but our topic is...

Ah, some parts are maybe usable, but our topic is everything flying :-)
Forum: User Product Reviews
09-30-2014, 10:03 PM
Replies: 5
Views: 1,021
Posted By uniLIGHT

Hi, what you mean with ground prodcuts? We are...

Hi, what you mean with ground prodcuts? We are specailized for aircrafts, but several items are also possible to use on other projects :-)
Forum: User Product Reviews
09-24-2014, 03:07 AM
Replies: 5
Views: 1,021
Posted By uniLIGHT

uniLIGHT is searching reviewers...

We are a young mechatronic company based in Austria, Europe and specalized on aircraft lighting systems since the last year. Our uniLIGHT products has been established since the last year in central...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.