RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: CzDavec
Showing results 1 to 16 of 16
Search took 0.06 seconds.
Forum: Glow Engines
07-06-2017, 06:36 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Landing and taxi in to pits

https://www.facebook.com/dave.carling.50/videos/394498337580573
Tried putting up a link to a couple of videos but the site wont enable them .
Sorry , will try a different way.
Forum: Glow Engines
06-27-2017, 10:05 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

2221831Hi Tom , Here's a couple of pics of my...

2221831Hi Tom , Here's a couple of pics of my Giant Stick with the 7 -77 in it. Flys it nicely . Should have shortened the nose up by an inch or two and it wouldn't have required as much tail weight.
Forum: Glow Engines
04-19-2017, 08:26 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Hi All, I figured I would add my 2cents worth...

Hi All,
I figured I would add my 2cents worth since I have finally gotten my 7-77 in the air. I have read the entire forum and followed Toms advice on limiting the throttle travel on the stock carb...
Forum: Glow Engines
07-22-2015, 05:30 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Roger, Let me take a look at my radial when I...

Roger,
Let me take a look at my radial when I get home today. I might be able to machine you a new cyl. mntg. ring for your engine. I would probably either need a sample or a very good drawing of...
Forum: Glow Engines
07-20-2015, 12:05 PM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Thanks Tom, I will look into one of the OS...

Thanks Tom,
I will look into one of the OS Carbs. I can machine it or an adapter for it . " Sometimes it pays to own a machine shop " <G> .
Roger, very sorry to hear about your Howard. That is my...
Forum: Glow Engines
07-14-2015, 07:03 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Thanks Bob, I will up the cutoff point just a...

Thanks Bob, I will up the cutoff point just a bit. I will also make sure to put the switch into the harness when I install it in the plane.

Dave
Forum: Glow Engines
07-14-2015, 05:27 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Thanks Tom, I will slightly richen up the low...

Thanks Tom,
I will slightly richen up the low end needle and I will reset my radio for around the 3/4 open mark. That was kind of my suspicion that the carb was to big. I have run into this before...
Forum: Glow Engines
07-13-2015, 09:12 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Thanks Roger, I got a hold of Miller and got...

Thanks Roger,
I got a hold of Miller and got the starter sorted out. It's amazing how much easier the engine starts when you can crank it over !!
I have a couple of questions on the break in...
Forum: Glow Engines
07-03-2015, 09:51 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Thanks Tom, I will check out the web site. None...

Thanks Tom, I will check out the web site. None of the LHS has one around here . I will also up the prop to the 22 x 12 for the next run.

Dave
Forum: Glow Engines
07-03-2015, 05:39 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Heli, where did you get the miller reduction for...

Heli, where did you get the miller reduction for your sulliven? I was looking online and didn't find one. I know what they look like. I guess I just wasn't searching in the right place, I borrowed a...
Forum: Glow Engines
07-02-2015, 06:22 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Okay Guys, I could use some tuning and set up...

Okay Guys,
I could use some tuning and set up tips. I finally ran my 7-77 on Sunday . 1st problem was my so called "Heavy duty , Hi Torque starter" Couldn't wind it over even on 24 volts . So I had...
Forum: Glow Engines
06-18-2015, 05:15 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Thanks for the input. I can work the math and...

Thanks for the input. I can work the math and blend the fuel down a little bit more to get closer to the optimum 7% . I figure a touch more oil in the mix won't hurt for the initial break in on the...
Forum: Glow Engines
06-17-2015, 01:23 PM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Thanks Guys, That was what I figured but wanted...

Thanks Guys, That was what I figured but wanted to vet it with you guys first. I am not used to an engine that uses such a low oil content . Buying the Cool power and mixing it down with the methanol...
Forum: Glow Engines
06-17-2015, 08:50 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Hi Guys, Have a quick question regarding glow...

Hi Guys, Have a quick question regarding glow fuel for the radials . I have the corsair almost finished and am ready to break in the engine. I can purchase methanol , no problem and can buy Klotz...
Forum: Glow Engines
01-05-2015, 08:19 AM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Thanks for the input, That's what I was looking...

Thanks for the input, That's what I was looking for. This forum and the people on it are what made my decision to buy the radial over a turbine .
Forum: Glow Engines
12-30-2014, 12:36 PM
Replies: 2,647
Views: 521,832
Posted By CzDavec

Hi, I am new to having a radial but have always...

Hi, I am new to having a radial but have always wanted one and Santa obliged me with a 7 -77 and a giant corsair to put it in. I have read this forum through and there is a ton of helpful advice...
Showing results 1 to 16 of 16


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.