RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: northernboater45
Showing results 1 to 21 of 21
Search took 0.04 seconds.
Forum: Speed - RC Gas Boats
07-25-2017, 02:07 PM
Replies: 3
Views: 1,791
Posted By northernboater45

good dependable rc setup for a 50 on gas boat

Any one know a good dependable rc setup for a 50 on gas boat.I currently have a spectrum set up,which is not my favorite
I put it​​​​​​ together all set to go,an low and behold it all stopped.This...
Forum: Speed - RC Gas Boats
07-13-2017, 03:31 PM
Replies: 6
Views: 1,180
Posted By northernboater45

Had the wiring turned around,this is how noobs...

Had the wiring turned around,this is how noobs learn.
Forum: Speed - RC Gas Boats
07-13-2017, 03:28 PM
Replies: 6
Views: 1,180
Posted By northernboater45

It's all good now wiring was turned around,this...

It's all good now wiring was turned around,this is how noobs learn.
Forum: Speed - RC Gas Boats
07-12-2017, 04:46 PM
Replies: 6
Views: 1,180
Posted By northernboater45

Binding a dx2 spectrum transmitter

I have a dx2. spectrum transmitter with a sr200wp receiver. They came out of bind.I can bind them but servos won't work.I,ve tried to make them work a lot in the last 2 days, but nogo ,any ideas? Is...
Forum: Speed - RC Gas Boats
05-03-2017, 06:01 PM
Replies: 7
Views: 1,998
Posted By northernboater45

Oil Ratio for Break-in

Need to know the brst oil-gas combination for my new zenoah 260 water cooled engine.This will be for the break in period.
Forum: Speed - RC Gas Boats
03-19-2017, 10:39 AM
Replies: 4
Views: 980
Posted By northernboater45

Thanks for your advice.

Thanks for your advice.
Forum: Speed - RC Gas Boats
03-18-2017, 03:13 PM
Replies: 4
Views: 980
Posted By northernboater45

painting a glass hull

Whats the best way to paint a fiberglass enforcer hull,take it to a body shop . I'm new at this ,can you tell?
Forum: Speed - RC Gas Boats
01-18-2017, 11:17 AM
Replies: 3
Views: 1,465
Posted By northernboater45

Thanks for the info

Thanks for the info
Forum: Speed - RC Gas Boats
01-17-2017, 08:28 PM
Replies: 3
Views: 1,465
Posted By northernboater45

northernboater45

What would be a better killswitch, a killerbee or a bonzi failsafe or are they the same?
Forum: Speed - RC Gas Boats
12-18-2016, 07:32 PM
Replies: 3
Views: 1,880
Posted By northernboater45

Swap meets in Florida?

Anyone know if the state of flordia has any boat races or swap meets.I'll be down in the destin area jan through mar . Any where in the state, it doesn't matter,thanks.
Forum: Speed - RC Gas Boats
12-15-2016, 03:57 PM
Replies: 18
Views: 2,732
Posted By northernboater45

Thanks for your advice but why can't you store...

Thanks for your advice but why can't you store them empty?
Forum: Speed - RC Gas Boats
12-14-2016, 04:19 PM
Replies: 18
Views: 2,732
Posted By northernboater45

iv bag gas tank

Anyone have an opinion on iv bag gas tank as opposed to a hard shell tank, undecided which way to go.
Forum: Speed - RC Gas Boats
12-12-2016, 05:39 AM
Replies: 2
Views: 728
Posted By northernboater45

northernboater45

Any one know where I can get an Iv bag gastank,can't seem to find one online,thanks Bob
Forum: RC Boats General Discussion
12-11-2016, 01:09 PM
Replies: 0
Views: 528
Posted By northernboater45

northern boater 45

where can I buy an Iv style gas bag tank for my enforcer boat, I don"t seem to be able to find one online?
Forum: Speed - RC Gas Boats
06-07-2016, 03:25 PM
Replies: 0
Views: 563
Posted By northernboater45

northern boater 45

Cured the waterpump problem by turning the carb block upside down. New problem.Put a replacement carb on and it started on the 3rd pull. Ran out of fuel after the float bowl Emptied.I pulled the...
Forum: Speed - RC Gas Boats
05-31-2016, 02:34 PM
Replies: 7
Views: 946
Posted By northernboater45

I finally found that out and I'm sure i'll be...

I finally found that out and I'm sure i'll be back for more info ,thanks again Bob
Forum: Speed - RC Gas Boats
05-30-2016, 05:47 PM
Replies: 7
Views: 946
Posted By northernboater45

Thanks for the diagram,appreciate it , but the...

Thanks for the diagram,appreciate it , but the main focus for me is where to put the the pulse line .Which port upper or lower, I'm not sure
Forum: Speed - RC Gas Boats
05-30-2016, 02:42 PM
Replies: 7
Views: 946
Posted By northernboater45

upnorthboater45

I cant get water pump on my enforcer with a zenoah engine to push water through it. I've tried 3 different pumps with no sucess.Is the pulse fitting suppose to be on the top or bottom.Mine is on the...
Forum: Speed - RC Gas Boats
04-10-2016, 04:13 PM
Replies: 1
Views: 1,071
Posted By northernboater45

stuffing tube

I have a 48 in enforcer type hull that had a weedwacker engine in it.I'm putting a zenoah in it, which brings up my question.The stuffing tube is about 2or3 in short. can I sleeve the tube with the...
Forum: RC Boats General Discussion
12-24-2015, 07:29 PM
Replies: 4
Views: 529
Posted By northernboater45

thanks for the info,I don't expect a rocketship,...

thanks for the info,I don't expect a rocketship, but I think performance will pick up a lot.
Forum: RC Boats General Discussion
12-23-2015, 05:32 PM
Replies: 4
Views: 529
Posted By northernboater45

Lightbulb weight difference

Being new to rc gas boating,(2yrs) I'm interested in maybe exchanging my homelite engine for a zenoah .I have an enforcer hull.Would there be any weight savings .I know the zenoah will spin up better...
Showing results 1 to 21 of 21


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.