RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Chrille
Showing results 1 to 14 of 14
Search took 0.57 seconds.
Forum: RC Jets
03-16-2008, 05:17 AM
Replies: 3,661
Views: 626,301
Posted By Chrille

RE: JetJoe OWNERS thread

Hello Mark !

I´am asking therefore I´am doing service to the Swedish Jet pilots turbine and i particular SimJet turbine. And have a great interest in balancing. I´ll do the balancing down to...
Forum: RC Jets
03-16-2008, 03:35 AM
Replies: 3,661
Views: 626,301
Posted By Chrille

RE: JetJoe OWNERS thread

Hello Mark !

I´am a bit confused about the figures of unbalance.
You are talking of gr/mm in the text and I can read mg on the Cab720 display is this value mg/mm or what ??
You say you set...
Forum: SimJet Turbine Direct Support
11-01-2007, 06:25 PM
Replies: 10
Views: 2,227
Posted By Chrille

RE: Simjet 1200 leaking fuel

Hi David !
The next time you will have problem with leaking fuel under the cover, just unwinde the cover put air pressure on the fuel pipe 2,5 - 3,0 bar spray (leakfinder) or similar liquid...
Forum: SimJet Turbine Direct Support
11-01-2007, 06:00 PM
Replies: 1
Views: 1,011
Posted By Chrille

RE: Clearence

Hello Pelle !

Set the play 0,10 to 0,15 and you'll be on the safe side.

MVH
christer
Forum: RC Jets
09-29-2006, 03:46 AM
Replies: 42
Views: 5,542
Posted By Chrille

RE: PLEASE GRANT MY WISH BVM !!

I´m just looking for airfoils, taper and sweep back on the main wing of the BVM Balasa Super Bandit. I´m rebuilding an old Spectre and will have a better wing, I´ll belive that a Bandit wing will...
Forum: RC Jets
09-27-2006, 01:39 PM
Replies: 0
Views: 664
Posted By Chrille

BVM Super Bandit Balsa

Do anyone know the airfoil shape of the wing on a Super Bandit bottom and topp spruce, wash-out,taper.
I´ll try to make a better wing for my Spectre.
Forum: JetCat Turbine Direct Support
11-11-2005, 08:27 PM
Replies: 3
Views: 6,422
Posted By Chrille

RE: Jet Cat P80 lubrication

Hello Mr. Matt

Yes I am almost finished with the reparation of the P 80. I have to build a new starter, front cowl, new combustion-chamber now it’s only the electronic missing. Maybe you know...
Forum: Off Topic Forum - Planes/Helis
11-10-2005, 03:07 AM
Replies: 44
Views: 8,307
Posted By Chrille

RE: Morgan Restoration Thread

Hello Tiger !

Why I did change the frame. Because the unfriendly weather here in Sweden to cars like the Morgan. Ex. You don`t drive around in a Morgan in wintertime, you have to place him in a...
Forum: JetCat Turbine Direct Support
11-08-2005, 01:23 PM
Replies: 3
Views: 6,422
Posted By Chrille

Jet Cat P80 lubrication

Can anyone tell ???

I`ve a P80 suffering from a crash and followed by fire. All parts under the front cover where melted down. Now I´am rebuilding the turbine but cant find any oil restrictor...
Forum: Off Topic Forum - Planes/Helis
11-06-2005, 06:13 PM
Replies: 44
Views: 8,307
Posted By Chrille

RE: Morgan Restoration Thread

Hello Tiger !

After reading your post´s about restoration a MORGAN +4 You put me back on the memory lane back in late `60 when I restore´d two Morgan´s totally stripped down change the frame...
Forum: Glow Engines
11-02-2005, 05:54 PM
Replies: 54,892
Views: 5,436,574
Posted By Chrille

RE: Welcome to Club SAITO !

Bill !

Yes I´ve a tight fit and the deep is measured the same as before with no press on the outer lip. About the spare parts in Sweden I think the price as vell as the supply is good. A rocker...
Forum: Glow Engines
11-02-2005, 04:56 PM
Replies: 54,892
Views: 5,436,574
Posted By Chrille

RE: Welcome to Club SAITO !

Hello Bill !

Have done my crank. Now it´s "straight" and run within a hundred of a millimeter measure´d on prop shaft just before thread start, you think it´s good enough ? The rocker...
Forum: Glow Engines
10-30-2005, 06:08 AM
Replies: 54,892
Views: 5,436,574
Posted By Chrille

RE: Welcome to Club SAITO !

Hi Bill !

Thank`s for your fast reply, Yes I have bent the valve-guides and I´m not very proud of it, ( I´ll try to attach some pic´s for better understanding) but I´m feeling much better...
Forum: Glow Engines
10-28-2005, 06:20 PM
Replies: 54,892
Views: 5,436,574
Posted By Chrille

RE: Welcome to Club SAITO !

Hello Everyone Need some good advice !
My new Saito FA 300TL suffer from a hard contact with terra firma. Crank is bent and the valve-guide for intake and exhaust is also bent ( right side...
Showing results 1 to 14 of 14


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.