RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: Simou
Showing results 1 to 20 of 20
Search took 0.53 seconds.
Forum: RC Jets
05-16-2011, 12:40 AM
Replies: 11
Views: 5,656
Posted By Simou

RE: turnigy 8-15 A UBEC on a rc jet

Even if old thread, i wanna report my experience. I'm using those UBEC 8-15 by Turnigy in 3 big scale planes, and i'm going to use them in a turbine jet. I always use them coupled: 2x 2s battery...
Forum: Gas Engines
02-18-2008, 07:34 AM
Replies: 74
Views: 9,306
Posted By Simou

RE: New SV100cc Twin From United Hobbies

The CDI that comes with is motor is rated from 4.8v to 6.0v . My battery pack wasn't fully charged as it had a 45min flight on a 6 servos sailplane, before to plug in the CDI.
Forum: Gas Engines
02-15-2008, 04:07 PM
Replies: 74
Views: 9,306
Posted By Simou

RE: New SV100cc Twin From United Hobbies

This evening it seems nearly to start.... but the CDI has gone..... puff.... blowed up. 5 NIMH 2300 cells not fully charged.
GRRRRR
Forum: Gas Engines
02-04-2008, 11:30 AM
Replies: 74
Views: 9,306
Posted By Simou

RE: New SV100cc Twin From United Hobbies

ty Francis for the reply,
my problem is that a few weeks ago i moved needles from their original position, and now i dont remember the originale setting!
I remember a strange number of turns,...
Forum: Gas Engines
01-30-2008, 07:50 AM
Replies: 74
Views: 9,306
Posted By Simou

RE: New SV100cc Twin From United Hobbies

I would like to know for sure the needle settings of a running V3 engine. Mine doesn't even seems to fire up. I'll dismantle the reed valve...
[&o]
Forum: Gas Engines
01-22-2008, 06:01 AM
Replies: 74
Views: 9,306
Posted By Simou

RE: New SV100cc Twin From United Hobbies

I've bought one of these engines V3, I cant get it to run, it kicks back a lot. I mounted it inverted on the bench, with mufflers and carb facing up. Soon I'll try with engine laying correctly.
...
Forum: Gas Engines
01-15-2008, 06:11 AM
Replies: 149
Views: 35,162
Posted By Simou

RE: HH100T 100cc twin Review

I'de bought one of these engines V3, I cant get it to run, it kicks back a lot. I mounted it inverted on the bench, with mufflers and carb facing up.
Soon I'll try with engine laying correctly.
...
Forum: Gas Engines
02-16-2007, 09:02 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

I hope this helps.

http://tinyurl.com/22xjyg

I wrote it in italian, the translation by google is terrible, please be patient....
:eek:

Simone
Forum: Gas Engines
12-05-2006, 03:45 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

also mine it is only the logical part, I kept the original CDI. With the second pickup I fire up the engine by hand, without any kickback. Soon I will share my code on my homepage.

Simone
Forum: Gas Engines
12-04-2006, 10:51 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

i've already done it ;) but I don't plan to sell anything.
I improved the logic part of the project you can see at http://www.modelbouw.gompy.net/newcdi/newcdi.htm, using a second pickup unit for...
Forum: Giant Scale Aircraft - 3D & Aerobatic
09-22-2006, 06:51 AM
Replies: 4,485
Views: 442,856
Posted By Simou

RE: YAK 54 TOC1

Please what is the diameter of the firewall?
what are the dimensions of the canister tunnel?
tnx in advance

Simone
Forum: Gas Engines
09-21-2006, 08:56 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

1/2 turn on these needles is an enormity... low needle affects full throttle too much. I didn't asked about RPM for adjusting purpose: gf45 is on a tug and I want to know the overall performance of...
Forum: Gas Engines
09-21-2006, 03:14 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

RichAur,
I agree... this engine is very difficult to properly tune.
What rpm should it turn an APC 20x8W?
tnx

Simone
Forum: Gas Engines
09-20-2006, 03:08 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

I bought a MVVS 45 IRS MG w/canister, instead..... ;)

....but for my tug plane CRRC would be better.

Simone
Forum: Gas Engines
09-20-2006, 02:21 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

Yesterday I tried a CDI from a new in box GF45i, same version of mine. Same kind of problems: the engine runs rich, even with the needle closed. I also tried another carb and even a new needle on my...
Forum: Gas Engines
09-15-2006, 03:28 PM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

I've found the best is with this mark opposite from the engine shaft... Is my magnetic pin mounted reversed??? Briefly, my engine runs rich, at a unstable rpm. Adjusting needles does not take any...
Forum: Gas Engines
09-15-2006, 02:25 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

After several trials, my motor still starts surging above half throttle. Idle is good. I have no cowl, tried 95 and 98 octane fuel, tried both synthetic and mineral oil, tried some works on the...
Forum: Gas Engines
04-16-2006, 04:24 PM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

I experience some trouble starting it inverted. It require many flip to prime, then it get immediately flooded and kick back hard. Holding the plane with vertical wings (the engine lays on his side)...
Forum: Gas Engines
03-27-2006, 07:09 AM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

mine has the metal carbi support and the rounded muffler, the ignition is similar to the black one but it is GRAY.

SMU
Forum: Gas Engines
03-22-2006, 04:31 PM
Replies: 1,644
Views: 281,121
Posted By Simou

RE: CRRC GF45i

... Someone has a video of this engine running well!?

tnx in advance

SMU
Showing results 1 to 20 of 20


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.