RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: whitemax
Showing results 1 to 15 of 15
Search took 0.50 seconds.
Forum: Beginners
12-09-2009, 09:05 AM
Replies: 14
Views: 1,421
Posted By whitemax

RE: covering wrinkles

i have heat gun, a tacking iron, and the little tacking iron for corners. oh well its just a trainer, that I learn a lot on so far. my 4* 40 will be better and the next after that. thanks for your...
Forum: Beginners
12-08-2009, 11:53 AM
Replies: 14
Views: 1,421
Posted By whitemax

RE: covering wrinkles

That is what I am thinking of. If I a perfect or close to perfect job my luck I will crash. but a ok job covering the plane will probably last a while. As long as it does not affect the...
Forum: Beginners
12-08-2009, 10:26 AM
Replies: 14
Views: 1,421
Posted By whitemax

covering wrinkles

Hi Everyone,

I have been covering my LT-40 and on the rear fin I have wrinkles (they are in the rear lower corner and I have it on both side too). I have used the heat gun and then tacking...
Forum: Beginners
12-04-2009, 12:09 PM
Replies: 9
Views: 991
Posted By whitemax

RE: cover iron help

no, but I will go get one and put it one on, thanks for the heads up.
Forum: Beginners
12-04-2009, 11:51 AM
Replies: 9
Views: 991
Posted By whitemax

RE: cover iron help

It looks like the non-stick or whatever that coating on the bottom of the tack iron is rubbing off? Is this normal?
Forum: Beginners
12-04-2009, 11:48 AM
Replies: 9
Views: 991
Posted By whitemax

cover iron help

Hi everyone.

I am covering my first plane. The problem I see is that there is some black stuff on my yellow covering. The tack iron is new. Is this normal? am I melting or burning the...
Forum: Beginners
11-30-2009, 10:37 AM
Replies: 7
Views: 729
Posted By whitemax

RE: 2.4ghz tx/rx Do I nee more than 4ch?

I would buy at least a 6 channel radio. That is the advise that I read from this site. I bought the 6ex.
Forum: Beginners
11-23-2009, 02:15 PM
Replies: 18
Views: 1,351
Posted By whitemax

RE: batteries

Think this post just confussed me more, but I bought a 4 cell 600 battery pack. That is what I got from this. Thanks for your help and input from this thread. I guess I could always buy a backup...
Forum: Beginners
11-23-2009, 09:51 AM
Replies: 18
Views: 1,351
Posted By whitemax

batteries

Good Morning Everyone,

I bought the futaba 6ex, what battery should I buy for the receiver? How many cells / voltage, eta? I looked at tower and ebay, and there are a lot to pick from...
Forum: Beginners
11-05-2009, 09:53 AM
Replies: 11
Views: 1,077
Posted By whitemax

RE: first kit build question / problem

raydar: did you mount the wing on perm?

The second wing came out perfect, and looking back you really cant tell from looking at the wing that it is off at all.

Thanks for your help!

...
Forum: Beginners
11-04-2009, 02:35 PM
Replies: 11
Views: 1,077
Posted By whitemax

RE: first kit build question / problem

I am already getting excited for my next build (and I have not finished this one yet), now figuring out different ways to build. I have been reading A LOT about building but not until you do it is...
Forum: Beginners
11-04-2009, 09:59 AM
Replies: 11
Views: 1,077
Posted By whitemax

RE: first kit build question / problem

thanks Charlie P for your insight.
Forum: Beginners
11-04-2009, 09:13 AM
Replies: 11
Views: 1,077
Posted By whitemax

first kit build question / problem

I have a quick question:

(Not that I can fix it now) BUT... I am building a Sig LT 40 and I just finished the first wing and the trailing edge where the ribs get installed was not lining...
Forum: Beginners
10-26-2009, 08:58 AM
Replies: 4
Views: 543
Posted By whitemax

RE: No Glow motor forum?

thank you for everyones help! Little slow I guess. haha
Forum: Beginners
10-25-2009, 08:03 PM
Replies: 4
Views: 543
Posted By whitemax

No Glow motor forum?

I am very new to rc planes and nitro, but how come there is no Glow Motor forum? Were would be a good place to ask questions about this? thanks,
Patrick
Showing results 1 to 15 of 15


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.