RCU Forums - Search Results
RCU Forums

Go Back  RCU Forums > Search Forums
Reload this Page >

Search Results

Register
FAQ
Community
Calendar
Today's Posts
Search
Vendor Directory
Notices
Search: Posts Made By: luftewaffe
Showing results 1 to 10 of 10
Search took 0.51 seconds.
Forum: T-Rex heli
04-18-2007, 09:15 AM
Replies: 4
Views: 531
Posted By luftewaffe

RE: help I have an offset between the autorotation and tail drive gears

Robert,

The height of the main gear and autorotation gear can be adjusted by loosening the set screws on the collar at the bearing on the top of the frame. The mesh can be set perfectly this...
Forum: T-Rex heli
04-18-2007, 08:39 AM
Replies: 22
Views: 3,097
Posted By luftewaffe

RE: Best belt for a t-rex 450 tail

Here's the link. Scroll down to about 4/5 of the way down. I also highly recommend this belt.

http://www.techmodelproducts.com/trex_450_parts.php
Forum: Gas Engines
04-18-2007, 08:34 AM
Replies: 20
Views: 3,287
Posted By luftewaffe

RE: Evolution 26GT - Difficuty Priming

Thanks everyone for the suggestions. I did get it started by putting some gas into the carb to wet the diaphragm. It started up on the first flip. I haven't had a chance to tune the engine yet,...
Forum: Gas Engines
04-15-2007, 06:11 PM
Replies: 20
Views: 3,287
Posted By luftewaffe

RE: Evolution 26GT - Difficuty Priming

Thanks ramduster - I squirted some gas into the carb and it started right up. It idles ok, but when I try to give it any throttle it quits around 30% power. This is my first gas engine. It may be...
Forum: Gas Engines
04-15-2007, 03:15 PM
Replies: 20
Views: 3,287
Posted By luftewaffe

RE: Evolution 26GT - Difficuty Priming

I tried that - covered it with a piece of tape - still wouldn't prime.
Forum: Gas Engines
04-15-2007, 02:29 PM
Replies: 20
Views: 3,287
Posted By luftewaffe

Evolution 26GT - Difficuty Priming

I just installed an Evolution 26 GT on a Goldberg Pitts 12 and am having difficulty starting it. It doesn't want to prime. The ignition is working fine and sending spark to the plug, but I can't...
Forum: Beginners
06-16-2006, 09:41 PM
Replies: 53
Views: 7,702
Posted By luftewaffe

RE: Crosswind Landings - Crab or side slip??

Fact is, a plane is affected by a crosswind. It exerts pressure on the fuselage and vertical stabilizer. If a plane is moving at 30mph with a right crosswind at 5mph, the combination of these two...
Forum: ARF or RTF
06-06-2006, 09:45 PM
Replies: 18
Views: 1,745
Posted By luftewaffe

RE: SIG LT-40 ARF

I built this LT-40 from a kit as my first plane. I made it a tail dragger - IMO the ground handling isn't bad at all. I have a OS 50 SX on it which is a great engine but almost too much power for...
Forum: Beginners
05-02-2006, 07:32 PM
Replies: 7
Views: 832
Posted By luftewaffe

RE: Another LT-40

I eliminated the trike gear because I like the look of a tail dragger. I am planning to eventually get into WWII scale aircraft and most of them are tail draggers. I am also a full scale pilot and...
Forum: Beginners
05-01-2006, 09:05 PM
Replies: 7
Views: 832
Posted By luftewaffe

Another LT-40

Hi all,

Just wanted to post a quick note to let you all know that I built an LT-40 over the winter with a lot of help from RCU (especially Ken's build thread). I made a few mods including...
Showing results 1 to 10 of 10


 
Forum Jump

Contact Us - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service -

Copyright © 2024 MH Sub I, LLC dba Internet Brands. All rights reserved. Use of this site indicates your consent to the Terms of Use.